User manual PROTECH MEGAMAX INSTRUCTION MANUEL

[. . . ] Never use other fuels that are explosive or fire hazardous. A wrong use of the fuel can cause serious injuries or damages. [. . . ] (Never use water to clean the car) · Check the condition of the air filter, and replace if necessary the foam insert. Check all nuts, bolts & screws are properly tightend. Use a little of oil or grease on turning parts if necessary. More steering Standard Less steering Standard Quick acceleration use the ref. 211 Front lower suspensionarm holder (at the back of the gearbox) Voorste ophangingsarm houder (achteraan de versnellingsbak) Support inférieur de bras de suspension AV (arrière du réducteur) 4x16mm TP screws Lägerböcke für Querlenker (aufs hintere des Getriebe) Zelftappende schroeven T57. Front upper suspensionarm holder (at the back of the gearbox) Voorste bovenste ophangingsarm houder (achteraan de versnellingsbak) Support supérieur de bras de suspension AR (arrière du réducteur) Vordere Lägerböcke für Querlenker oben (aufs hintere des Getriebe) T57. Nut lock A600 Stud lock A601 Nut lock A600 Stud lock A601 Nut lock A600 Stud lock A601 Insert the rear drive shaft before the assembly of the rear lower arm. Mounting the front gear box / Monteren van de voorste versnelling Montage du train avant / Montierung des vordere Getriebe M4x15mm screw Schroef Vis Schraube MA2039 M4x10mm F/H screw Schroef Vis Schraube MA2268 4x16mm F/H TP screw Zelftappende schroef Vis autotaraudeuse Blechschraube MA2249 Main chassis Chassis Chassis principal Chassis T57. Fixing the front shock stay / Monteren van de voorste schokdempersteun Montage du support AV d'amortisseurs / Montierung des vordere Stoßdämpferplatine Mounting the rear shock stay / Monteren van de achterste schokdempersteun Montage du support AR d'amortisseurs / Montierung des hintere Stoßdämpferplatine Nut lock A600 Stud lock A601 058 4x4mm Set screw Stelschroef Vis allen Gewindestifte MA2052 5x4mm Set screw Stelschroef Vis allen Gewindestifte T57. Nut lock A600 Stud lock A601 Adjust the screws to keep the space of the brake pads less than 2, 5 mm · 028 Put the center drive shaft before installing the slipper clutch unit Plaats de centrale aandrijfas voor dat u de `slipper' koppeling installeert. M3x15mm F/H screw Schroef Vis Schraube MA2033 3x15mm F/H screw Schroef Vis Schraube MA2216 Pull down the shock and fill it with silicone oil · Move the piston slowly up and down to remove the airbubbles · Fix the pressure membrane in the shock cover · Screw the shock cover with membrane on the shock body · Use PROTECH silicon oils for better performance SL250 SL300 SL350 SL400 SL450 SL500 Silicon oil 250cps SOFT Silicon oil 300cps Silicon oil 350cps Silicon oil 400cps Silicon oil 450cps Silicon oil 500cps HARD Put the Nylon nuts in the side plate mount before you fix it to the chassis. Screw Schroef Vis Schraube Receiverbox cover Deksel ontvangerdoos Couvercle du boïtier RX Deckel von Empfängerdose T70. Adjustable brake nut Stelschroef Vis de réglage Stellschraube M3x3mm Set screw Stelschroef Vis allen Blechschraube MA2050 Spring Veer Ressort Feder M3x3mm Set screw Stelschroef Vis allen Blechschraube MA2050 Slide the nylon nuts into the groove of the engine mounts. Fit the flywheel using a plier and cross wrench. [. . . ] First you have to adjust your engine as in the manual delivered with the engine. Adjust the clutch shift timing for your track conditions with the 4x4mm set screw. [. . . ]