User manual PVG HEATOR SRE 804 TC

[. . . ] SRE 80x TC 3 2 6 5 4 > 1 9 MANUEL D'UTILISATION GEBRAUCHSANWEISUNG BRUGSANVISNING INSTRUCCIONES DE USO OPERATING MANUAL ISTRUZIONI D'USO GEBRUIKSAANWIJZING MANUAL DE INSTRUES 2 12 22 32 42 52 62 72 Dear Sir, Madam, Congratulations with your purchase of a portable domestic heater. You have purchased a quality product, which will serve you for many years to come. This, of course, provided you use the heater correctly. Please read these Directions for Use first, to ensure maximum lifetime for your heater. [. . . ] The latter can be changed with the adjustment keys (refer to Section E). Prior to igniting the heater, always check for sufficient fuel in the removable tank. E SETTING THE REQUIRED TEMPERATURE The temperature setting can only be adjusted, when the heater is burning. Use the adjustment keys to adjust the temperature. First press either of the two keys to will start blinking). Next, adjust switch on the function (the C mark and 4-digit the temperature using the key on the right (Mmin. ) to set the temperature to a higher setting and the key on the left (Nhour) to lower the temperature. Press once to increase the value one step. After approximately 10 seconds the C mark and 4-digit will stop blinking and the setting will be locked (Fig. The available temperature settings range from 6C minimum to 28C maximum. When the heater has been unplugged (or after a power failure), the temperature will reset to the factory setting of 20C. 4 46 F USING THE TIMER The timer allows you to switch on the heater automatically at a preset time. In order to switch on the timer, the correct time must have been set (refer to Section C) and the heater should be off. Follow the procedure below: 1 Press the button and then the TIMER key will start blinking. immediately after that. The TIMER light and the 4-digit 2 Use the adjustment keys to set the time at which the heater must ignite. Use the key on the left (Nhour) to set the hours and the key on the right (Mmin. ) to set the minutes (interval of 5 minutes). 3 After approximately 10 seconds the 4-digit will show CLOCK again and the TIMER indicator light will light up, indicating that the timer function has been activated (Fig. G). G: The TIMER indicator light indicates that the timer function has been switched on. 4 The timer will ensure that the room will have been heated to approximately the required temperature at the set time. G H In case of any malfunctioning the information display will tell you what is the matter. When you want to switch off the heater and ignite it again with the timer, all you have to do is press the TIMER key (refer to Section G). Press the button once to clear the timer setting. SWITCHING OFF THE HEATER There are two ways to switch off the heater. The information display will show the CLOCK signal. Within approximately one minute the flame will have extinguished. 2 Press the TIMER key , when you want to switch off the heater and ignite it again with the timer the next time. This not only switches off the heater, but it also activates the timer function. You can change the required time with the adjustment keys (refer to Section F). THE INFORMATION DISPLAY The information display not only serves as an indicator of the (set) time and temperature (sections C, E, and F), it also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter: CODE INFORMATION Temperature within the heater too high. Contact your dealer. efefeee- 0 0 1 1 2 5 6 4 47 e- 7 e- 8 e- 9 Room temperature above 32C. [. . . ] In case of emergency you may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher. 10 TIPS FOR SAFE USE 1 2 3 4 Make sure that children are always aware of the presence of a burning heater. Do not move the heater when it is burning or still hot. Do not refill nor service the heater when it is burning or still hot. Position the front of the heater at a distance of minimum 1. 5 metres from walls, curtains, and furniture. [. . . ]