User manual PYLE PDCD4000

[. . . ] 2. Disc Tray The disc is placed on this tray. Pressing the disc tray OPEN/CLOSE buttons will open or close the tray. 3. OPEN/CLOSE(Disc Tray Open/Close Button) Press to load or eject the disc. Each press will open or close the disc tray. [. . . ] NOTE: Tray will not open unless PAUSE button has been pushed first. LCD These liquid crystal displays (LCD) indicate the track numbers, time (minutes, seconds, frames), etc. PLAY/PAUSE(Play/Pause Button) Each press of the PLAY/PAUSE button cause the operation to change from play to pause or pause to play. TRACK(Skip button) This button selects the track to be played. +10:press this button to forward 10 tracks. JOG DIAL(+FWD&-REV) *Speed Control Rotating this dial in play mode will change playback speed accordingly. Rotate clockwise, the player speeds up; rotate counter-clockwise, the playback slows down. *Searching Rotating this dial in pause mode, the player will forward or backward to the desired point for start. The searching speed changes according to the dialing speed. It can be carried out by 1 frame increments. CUE(Cue button) Pressing the CUE button during play provides a return to the position at which play was started. ·The connection cords and the remote control connection cable are supplied with the main unit. ·Be sure to use the remote control connection cable which has been supplied. Use of another cable might cause damage. 6 BASIC OPERATION Loading and Ejecting the Disc Open the tray When the disc tray is closed, press the OPEN/CLOSE button to open the disc tray(This may be done on either the player or the remote control side. ) Place a disc in the disc tray Press the OPEN/CLOSE button to close the disc tray. The disc tray will close and the preparation for disc play will begin. When preparation is completed, the total tracks number & total playing time will display. To the desired track 7 TRACK SKIP To go back through the tracks To advance through the tracks Tracks change as follows This is for a disc containing 4 tracks Tracks change as follows When this button is pressed once , the CD player will When this button is pressed once, the CD player will skip backward to the beginning of the track. Pressing twice advance to the beginning of the next track. will skip backward to the previous track. Operation of Play, Pause and CUE 1. Press the PLAY/PAUSE button to switch the operation between PLAY and PAUSE. The indicator LED is illuminated during play, and blinking when in pause. Press the CUE button while in pause mode to memorize the point. The CUE LED will light after being memorized. When CUE LED is illuminated and in Play mode, pressing the CUE button goes back to the memorized point and is in pause mode. Press PLAY button again to perform from the cue point. 5. [. . . ] When the tempo of the music of the 9 selected CD player is slow compared to the tempo of the other player, move the slider to the + side and match the tempo. The following example is for matching the pitch of UNIT 2 to the pitch of the music being played on UNIT 1. UNIT 1 is playing. Press PLAY/PAUSE to start UNIT 2. Listen to UNIT 2 in your headphones. When UNIT 2 is slow compared to UNIT 1 When UNIT 2 is fast compared to UNIT 1 Beat Matching Using Pitch Bend A description of the procedure for matching the beat of UNIT 1 and UNIT 2 using the PITCH BEND stick is given below. This example is for matching the beat of UNIT 2 to the beat of the music being player on UNIT 1. (This procedure can be done on either Unit. ) After Matching the BPM's BPM (Beat Per Minute) is the same, however the bass beats are not matched. When UNIT 2 is ahead. When UNIT 2 is behead. BEFORE SWITCHING OFF THE POWER When you have finished using the CD player, before switching off the power be sure that the disc tray has 10 been closed with the OPEN/CLOSE button. Do not switch off the power when the disc holder is open. [. . . ]