User manual PYLE PLCD48MP3

[. . . ] When the temperature reaches a preset level, the protection circuit halts all unit operations. If this should happen, open a window and allow the car to cool. Condensation Moisture can condense on the laser lens of the CD changer during rainy and humid days, or right after the heater is turned on in the car. If this should happen the unit will not operate correctly. [. . . ] · Return the carpet to its original position allowing the bolts to stick through. 5 · Once more, use the hexagonal nuts to attach the changer on top of the carpet. 9 INSTALLATION Procedure for Installation on Carpet (at a 45° angle) 1 · Set the built-in anti-vibration boards on both the left and right sides to the 45° installation position "45°". · Attach the left and right brackets (A) using the hexagonal bolt (M4 x 5). · Attach the left and right brackets (A) to their respective brackets (B) using the hexagonal bolts (M6 x 12) and the hexagonal nuts (M6). Built-in anti-vibration board position Hexagon bolts (M6 x 12) Hexagonal bolts (M4 x 5) 2 · Pull back the carpet and determine where to attach the unit. · Stick the supplied double-sided tape to the bottom of the brackets (B) and peel off the paper backing. · Affix the unit to the floor by pressing in place. 3 · Remove the hexagonal nuts and take off the changer. 4 · Using a knife, cut "X"s in the carpet directly above the brackets (B) bolts. · Return the carpet to its original position allowing the bolts to stick through. 5 · Once more, use the hexagonal nuts to attach the changer on top of the carpet. 10 INSTALLATION Procedure for Installation (Suspended Position) 1 · Confirm that the built-in anti-vibration boards on both the left and right sides are set to the horizontal installation position "0". · Attach the left and right brackets (A) using the hexagonal bolt (M4 x 5). Built-in anti-vibration board position Hexagonal Bolts Hexagonal Bolts 2 · Determine the mounting location and drill four mounting holes. 3. 6ø 3 · Attach the CD changer with the tapping screws (M5 x 12). 11 HANDLING THE DISCS Dirt, dust, scratches and warpage cause sound skips during playback and a deterioration of sound quality. Use compact discs that have the mark shown on the right. Fingerprints and dust should be carefully wiped off the disc's signal surface (glossy side) with a soft cloth. Unlike conventional records, the compact disc has no grooves to collect dust and microscopic debris, so gently wipe with a soft cloth should remove most particles. Wipe in a straight motion from the inside to the outside of the disc. Upon pressing this button once, "REPEAT ONE" will be displayed on the LCD, and the playing will be repeated. When passed long, "REPEAT ALL" will be shown the Track is repeated in all disc. 14 Random Play Button (Track or DISC Random) - (5) This is used for random selection Disc play, and sequence. "RANDOM ONE" is displayed in the Upper left corner of LCD commander, and disc selection will begin random play. Press this button for a second, "RANDOM ALL" will be shown on the display. When "RANDOM ALL" function is activated, all tracks of each CD will be played in random order until all of them have been played once. To release the random selection function, push the random button again. Play/Pause Button (Play/Pause) - (6) To pause all play functions of CD Changer, push the "Pause" button. To return to play mode, press the "Pause" button again. Disc Selection Button ( + / ­ ) - (7) Press + / ­ button to select the desired DISC. Power Button (Power On/Off) - (8) Press this button to turn On/Off the changer. * When the pause mode is maintained for 5 minutes or more, the power will be automatically turned off. [. . . ] · RESET SWITCH A reset switch is located at the bottom of the FM modulator can only activated by a thin pointed object when: 1. After all the wiring installation completed. If abnormal disc operation occurs. 20 Control and Function Keys 1 0. 5A 2 3 4 RED PIN K A BL CK 5A A BL A BL CK 1. +12V TO IGNITION Connect the red power wire (with in-line fuse holder) to a point in your vehicle's fuse block that has power only when you turn the vehicle's key to either the accessory (ACC) or START position. [. . . ]