User manual PYLE PLCD87

[. . . ] DIN FRONT/REAR-MOUNT This unit can be properly installed either from "Front" (conventional DIN Frontmount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. 3 (Fig. 6. Dashboard Nut (5mm) Spring washer Screw (5 x 25mm) Screw Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. [. . . ] Press the OPEN button and then reinstall the front panel again. Bottom Button 4. For safekeeping, store the front panel in the supplied protective case immediately after being removed. Protective Case Front Panel 5 WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR (BLACK) AUX IN IGNITION RED SWITCH (B+) MEMORY YELLOW BACK-UP BLACK GROUND (B­) POWER ANTENNA BLUE Rch RED Lch WHITE (GREY) RCA CABLE Rch RED Lch WHITE FRONT Lch SPEAKER WHITE WHITE/BLACK GREEN GREEN/BLACK GREY GREY/BLACK VIOLET VIOLET/BLACK FRONT Rch SPEAKER REAR Lch SPEAKER REAR Rch SPEAKER 6 OPERATION 7 8 25 1 12 13 16 2 6 10 11 15 19 20 21 14 22 23 24 18 4 5 9 17 3 26 GENERAL OPERATION · ON/OFF Switch on the unit by pressing any button [except OPEN button (7)]. When system is on, press PWR button (9) to turn off the unit. · FACEPLATE RELEASE Press OPEN button (7) to detach the removable faceplate. · SOUND ADJUSTMENT Press SEL button (10) shortly to select the desired adjustment mode. The adjustment mode will change in the following order: 7 VOL (Volume) BAS (Bass) TRE (Treble) BAL (Balance) FAD (Fader) By rotating AUDIO ADJUST knob (8) clockwise or counter-clockwise, it is possible to adjust the desired sound quality. · LOUDNESS Press BND/LOU button (13) for several seconds to reinforce the bass output. Press it for several seconds again to release this function. OPERATION · SET THE CLOCK Press and hold DSP button (15), until the clock is shown on the display and flashes, then press the TUNE/TRACK button (17) to change minutes or TUNE/TRACK button (16) to change hours. · SELECT MODE Press MODE button (6) shortly to choose desired listening mode. radio mode to CD mode to AUX IN mode) The unit can be connected a portable audio player through the AUX IN jack (back of the unit). · MUTE Press MU button (3) to silence the receiver. · LIQUID CRYSTAL DISPLAY Exhibit current frequency and activated functions on the display (25). · EQUALIZATION Press P-EQ button (11) to turn on equalization function and to select desired audio mode. There are five kinds of mode as below: FLAT CLASSICS POP M ROCK M DSP OFF Note: If press RESET button (26), the unit can't work yet, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the front panel. RADIO OPERATION · BAND SELECTION At tuner mode, press BND/LOU button (13) to select the desired band. The reception band will change in the following order: FM1 FM2 FM3 AM · STATION SELECTION Press TUNE/TRACK button (16) or TUNE/TRACK button (17) shortly to activate automatic seek function. Press for several seconds until "MANUAL" appeared on the display, the manual tuning mode is selected. If both buttons have not pressed for several seconds, they will return to seek tuning mode and "AUTO" appeared on the display. · LOCAL/DISTANCE Press LO button (2) to select between local and distant stations. Local setting for reception of strong station, and a distant setting for reception of weaker stations. This function is effect dring AUTO SEEK operation. · MONO/STEREO Press MONO button (1) to select mono or stereo mode. You can sometimes improve reception of distant staions by selecting mono operation. · REMOTE SENSOR Point the remote control handset to the remote sensor IR (12). [. . . ] · COLOR BUTTON Press the COL button (4) to adjust the color of the LCD display. There are 7 kinds of color to be selected. NOTE ON CD-R/CD-RW DISCS · On this unit, in addition to an audio CD, you can play your original CD-R or CD-RW that contains audio titles. · However, depending on the condition of the recording equipment or the CDR or CD-RW itself, some CD-Rs or CDRWs cannot be played on this nite. · DO NOT stick paper or tape, etc, onto label side or the recording side of any CD-R/CD-RW, as it may cause a malfunction. CD OPERATION · SELECT TRACKS During CD operation, press TUNE/TRACK button (17) or TUNE/TRACK (16) to move to the previous track or the following track. [. . . ]