User manual PYLE PLE420P

[. . . ] We're confident that this product will provide you with many years of outstanding musical entertainment. i owner's manual table of contents Ple420p i 1 2 3 congratulations table of contents general features specifications 4-5 6 7 8-9 1 0 features and controls mounting and installation electrical connections system wiring precautions and troubleshooting 1 general features ple420p 4 band parametric controls pre-amp DVD & AUX input via RCA jacks ple420p subwoofer output 3. 5mm DVD input jack blue light illumination frequency gain control rotary fader rotary band control 6 channels RCA outputs remote power on/off output volume control input gain adjustments 2 owner's manual specifications ple420p ple420p 4 band parametric SUB 150Hz, LOW 400Hz, MID 2. 5KHz, HI 15KHz 18dB 15 Hz - 30 KHz (+/­ 1 dB) 200 mV < 0. 03% 10K Ohms 90 dB 50 dB 200 mA 12V DC Neg. Ground boost/cut frequency response input level (for 400mV output) total harmonic distortion (THD) (at 400mV output) output impedance signal-to-noise ratio (S/N) separation current drain power supply voltage dimensions (W x H x L) mm inches 178 x 28 x 105 7 x 1. 1 x 4. 1 3 features and controls ple420p front rear 4 owner's manual features 1. fader control Connects to the DVD source with 3. 5mm plug cable. [. . . ] connect to power source as follows: +12V: Connect a red wire of at least 12 gauge to the car battery or other power source. GROUND: Connect a black wire of at least 12 gauge to car chassis for ground connection REMOTE: Connect an orange wire to remote activating (12V DC) wire of car stereo or other head unit. 13-15. subwoofer/rear/front channel outputs 16-17. DVD/AUX input gain adjustments power connections 5 mounting and installation ple420p 4 x 6 mm machine screw (4) dashboard mounting Please take the time to install your new Pyle Signal Processor securely, according to this diagram, using the hardware provided. Signal Processor enclosure This Half-DIN size unit can also be installed in the dash adjacent to the head unit, provided that there is a slot available. Mounting Bracket 4 x 12 mm self-tapping screw (2) 4 mm spring washer (2) 4 mm plain washer (2) wiring tips When making electrical connections to your amplifier, please observe the following: Connect 12V DC from a constant battery source to a +12V slip-on spade terminal and install a one (1) amp fuse in line. Connect the signal processor's GROUND to a good chassis ground, near where the unit is mounted, or to the case of the head unit. Connect the signal processor's REMOTE TURN-ON lead to the remote turn-on lead out of the head unit, and install a 1/2 amp fuse in line. (A relay should be used if turning on more than one component, such as EQ's, crossovers or amplifiers. ) Connect stereo RCA cables from the head's left and right front outputs to the left and right inputs of the signal processor. Connect stereo RCA cables from the left and right outputs, (and low, mid and high outputs if applicable), of the signal processor to the left and right inputs of your amplifier(s) or additional signal processor(s). Turn the unit on, and adjust the input gain on the signal processor to match the output of the head unit (1/2, or at center position, is about 1 V). Be careful not to overdrive the input of your amplifier(s) or signal processor(s). Adjust each of the crossover or equalizer controls to achieve the desired sound characteristics. 6 owner's manual electrical connections ple420p rear RED WIRE ORANGE WIRE Fuse 1A Fuse 0. 5A to remote turn-on +12V head unit 12V battery BLACK WIRE 7 system wiring basic system application using front, rear, and subwoofer amps ple420p left and right DVD outputs from head unit left and right DVD inputs + ­ + REAR CHANNEL power amplifier L REAR CHANNEL speakers R ­ + ­ + FRONT CHANNEL power amplifier L FRONT CHANNEL speakers R ­ 8 SUB CHANNEL power amplifier + L ­ SUB CHANNEL speakers R + ­ owner's manual system wiring basic system application using a 4 channel amp and subwoofer amp ple420p left and right DVD outputs from head unit left and right DVD inputs + + ­ + 4 CHANNEL power amplifier ­ L/R REAR speakers L/R FRONT speakers ­ + ­ SUB CHANNEL power amplifier + L ­ SUB CHANNEL speakers R + ­ 9 precautions ple420p · Never drive with the volume raised so high you cannot hear what is occuring in traffic around you. · Be aware that repeated exposure to excessive volume levels can permanently damage your hearing!· Keep all electronics away from moisture, dust, extreme heat or extreme vibrations. · Pyle Audio products are capable of sound pressure levels in excess of 150 dB. Continuous exposure to sound pressure levels over 100 dB may cause permanent loss of hearing. Use common sense and PRACTICE SAFE SOUND. troubleshooting If you experience. . . [. . . ] This R. A. # must appear on the outside of your package and on all paperwork relating to your return. When returning a product to us for warranty service it must be carefully packed and shipped prepaid to: R. A. # Pyle Service Center 1600 63rd Street Brooklyn, NY 11204 You must also include the following items: · A copy of your sales receipt or other proof of purchase · A brief letter indicating the problem you are experiencing · include in your letter your return address, daytime phone number, and R. A. number · also include a check or money order for $12. 00 for return shipping, handling, and insurance, or provide your Visa/MC number with expiration date. [. . . ]