User manual PYLE PLE755S

[. . . ] Left and right channels are displayed independently at peak levels. power indicator LED this LED is illuminated when the unit is properly powered, grounded and the remote power has been turned on. fader control · in a 4 Speaker system, rotating the knob to the FRONT side increases the level of the front speakers; rotating to the REAR side increase level of the rear speakers. At mid position, both sets of speakers are at maximum level. [. . . ] this LED is illuminated when the unit is properly powered, grounded and the remote power has been turned on. · in a 2 Amplifier, 4 Speaker system, rotating the knob to the FRONT side increases the level of the front speakers; rotating to the REAR side increase level of the rear speakers. At mid position, both sets of speakers are at maximum level. · in a 2 Speaker system, the fader control should be rotated to the position which provides highest levels for both sets of speakers. volume control equalizer control subwoofer frequency control subwoofer boost control power connections allows adjustment of sound level for particular program material or source. this seven-band equalizer gives you control over the output levels at various frequencies. lets you adjust the subwoofer frequency and crossover point from 40-400 Hz. lets you adjust the subwoofer boost level from a 0 to +18 dB increase. connect to power source as follows: +12V: Connect a red wire of at least 12 gauge to the car battery or other power source. GROUND: Connect a black wire of at least 12 gauge to car chassis for ground connection REMOTE: Connect an orange wire to remote activating (12V DC) wire of car stereo or other head unit. subwoofer channel outputs front channel inputs RCA cables are used to connect the sub outputs to the subwoofer amplifier inputs. RCA cables are used to connect the front input signal from head unit or other source. 7-Band Equalizer with Subwoofer Crossover and Bass Boost center frequencies 65 Hz · 150 Hz 400 Hz · 1. 4 KHz 2. 4 KHz · 6 KHz 15 KHz 40 - 400 Hz 0 - +18 dB 20 - 20 KHz (+/­ 1 dB) 400 mV < 0. 03% 10K Ohms 90 dB 50 dB 450 mA 12V DC Neg. Ground 160 x 29 x 117 6. 3 x 1. 1 x 4. 6 subwoofer crossover bass boost frequency response input level (for 400mV output) 7 total harmonic distortion (THD) (at 400mV output) output impedance signal-to-noise ratio (S/N) separation current drain power supply voltage dimensions (W x H x L) mm inches electrical connections P L E 7 0 2 B· P L E 7 5 5 S rear OUTPUT SUB INPUT LINE PLE702B RED WIRE Fuse 6A BLACK WIRE 12V battery rear SUB Fuse 0. 5A ORANGE WIRE to remote turn-on +12V 8 head unit OUTPUT INPUT FRONT LINE PLE755S REAR Fuse 1A RED WIRE BLACK WIRE Fuse 0. 5A ORANGE WIRE to remote turn-on +12V head unit 12V battery mounting and installation P L E 7 0 2 B· P L E 7 5 5 S mounting Please take the time to install your new Pyle Signal Processor securely, according to this diagram, using the hardware provided. This Half-DIN size unit can also be installed in the dash adjacent to the head unit, provided that there is a slot available. 4 x 6 mm machine screw (4) dashboard wiring tips When making electrical connections to your amplifier, please observe the following: Connect 12V DC from a constant battery source to a +12V slip-on spade terminal and install a one (1) amp fuse in line. (six (6) amp fuse for PLE702b case) Connect the signal processor's GROUND to a good chassis ground, near where the unit is mounted, or to the case of the head unit. Connect the signal processor's REMOTE TURN-ON lead to the remote turn-on lead out of the head unit, and install a 1/2 amp fuse in line. (A relay should be used if turning on more than one component, such as EQ's, crossovers or amplifiers. ) Connect stereo RCA cables from the head's left and right front outputs to the left and right inputs of the signal processor. Connect stereo RCA cables from the left and right outputs, (and low, mid and high outputs if applicable), of the signal processor to the left and right inputs of your amplifier(s) or additional signal processor(s). [. . . ] Check that: · Wiring is not loose or cables misconnected/disconnected. · RCA cables are not faulty. 13 limited warranty policy amplifiers All Pyle products are carefully constructed and thoroughly tested before shipment. Products purchased in the USA are warranted to be free of defects in material and workmanship for two (2) years from the date of purchase. This warranty is limited to the original retail purchase. [. . . ]