User manual PYLE PLHR76 Reference Guide

[. . . ] LUD When reduce volume to half level, press it to enhance the bass effect. 8. ST BUTTON Press ST button to stereo reception for radio stations. 9. OPEN /EJECT Slide it down then you can insert the CD disc into the CD compartment or eject the disc. 10-11-12-13-14-15. To memorize the current frequency, press any one of the six preset Buttons hold for more than 2 seconds. To recall the preset memory, press one of the preset buttons [1-6]. [. . . ] Long press 1 TOP button to select the first track/chapter to play. In CDP mode, press 2INT button to play the first 10 seconds part of each song, press it again to stop scanning and retain playing the song currently selected. In CDP mode, press 3RPT button to play the current track repeatedly. In CDP mode, press 4RDM button to play the track in random order. G. In mp3 mode , press the 5-10/6+10 buttton to select back 10 tracks or next 10 tracks. 16. MUTE BUTTON Press it to eliminate the sound immediately. 17. DISP BUTTON Press DSP button immediately to recall time display, then press and hold this button for three seconds until the time is blinking. And press VOL+ button to adjust hour or VOLbutton to adjust minutes. 18. APS/SEARCH BUTTON IN RADIO MODE: When short pressing, the radio searches for each preset station. When the field strength level is more than the threshold level of stop level, the radio is holding at that preset number for few secretary with releasing mute, and than searches again. In FM band, FM 1, FM 2 and FM 3 is checked one at a time. When long pressing (more than 1 second), the radio searches from the current frequency and checks the signal strength level until 1 cycle search is finished. And then 6 strongest stations are preset to the corresponding preset number. The AS operation is implemented in the each band of selected band. If no such song, NOT FND will be shown on display. 19. BAND/ID3: During radio mode:Press it to select your desired radio band and the band which is selected will be displayed on LCD. During mp3 mode :Press search button to working Id3 as follow: (depend on the disc used for Mp3) File folder song artist album 20. POWER BUTTON 21. FLASHING LED Press it(more than 1 second) to turn off and short press to turn on the unit. If the front panel is not on the main unit, LED will be flashing. 22. RESET RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object. The RESET button is to be activated for the following reasons: -Initial installation of the unit when all wiring is completed. -All the function buttons do not operate. Note: If press RESET button, the unit can't work yet, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the front panel. 23. LOC When in the radio mode, press it to select local or distance broadcast station receive sensitivity . NOTE: The SCAN button on the remote controller(for RC version only) SCAN BUTTON Press it to scan up by one channel step with station detection. If a valid signal has detected, the current frequency is blinked with in 5 seconds, then press it again to stop scan and remain the current frequency; otherwise, the unit continue to scan up by one channel step with station detection 5 seconds later. 5 ELECTRIC CONNECTION WIRING CONNECTION AUX cable(optional) ANTENNA CONNECTOR RCH RED LCH WHITE IGNITION RED SWITCH(B+) MEMORY(B+) YELLOW GROUND(B-) BLACK AUTO BLUE ANTENNA FRONT FUSE BOX RCA OUTPUT CABLE(optional) RCH RED LCH WHITE FRONT WHITE GREY GREY/BLACK WHITE/BLACK Lch SPK REAR GREEN GREEN/BLACK VIOLET VIOLET/BLACK Rch SPK REAR Lch SPK Rch SPK NOTE: In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level. 6 INSTALLATION DASH BOARD HEX NUT METAL MOUNTING STRAP SPRING WASHER PLAIN WASHER TAPPING SCREW CONSOLE SLIDE BRACKET HOUSING HEX BOLT 7 INSTALLATION HOW TO REMOVE AND INSTALL THE FRONT PANEL 1. Press the release button and the right hand side of the front panel will release (FIG. 1) . Pull-off the front panel(FIG. 2) and Keep front panel into the case(FIG. 3). To install the front panel, insert the panel into the housing and make sure the panel is properly installed(FIG. 4). [. . . ] otherwise, abnormalities occurs on the display or some keys will not function properly. REMOVING THE FRONT PANEL FRONT PANEL FRONT PANEL RELEASE BUTTON FIG. 1 PROTECTIVE CASE FIG. 2 INSTALLING THE FRONT PANEL FRONT PANEL FIG. 3 FIG. 4 8 NOTES DISC PLAY: CLEANING DISCS Before playing, clean the disc with a clean, lint-free. Flip the disc in the direction of the arrow. NOTE 1: Do not use so solvents such as benzine, thinners. Commercially available cleaners or anti static spray damage the unit. [. . . ]