User manual PYRAMID PW848US-X DATASHEET

[. . . ] Before use, perform an advance check as described in this manual. Introduction Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from improper use of this product. Please read the following items before use This Case is a precision device designed for use at a water depth within 40 m. Please use the Case correctly after sufficient understanding of the contents of this manual in regard to handling of the Case, checks before use, maintenance, and storage after use. [. . . ] Handling After Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Wipe off any waterdrop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Take out the digital camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Wash the Case with pure water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Dry the Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintaining the Waterproof Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Remove the O-ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 EN 6 How to Apply Grease to the O-ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Install the O-ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Replace consumable parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 En EN 7 1. · Is silica gel inserted all the way at the specified location?· Is the O-ring attached properly to the opening on the Case?· Is there any dirt or foreign matter on the O-ring or the O-ring contact surface on the front lid?· Is the waterproof function maintenance performed?For details of the maintenance, see "6. Maintaining the Waterproof Function" (P. 24) of this manual. EN 17 Seal the Case 1 Close the Case gently while aligning the mounting projection of the rear lid and groove. · The Case is sealed. En Close CAUTION: · If the open/close dial is not fully turned, the Case will not be sealed. · Close the rear lid of the Case so that the lens cap or LCD hood strap doesn't catch. If it catches, water leaks may result. Check the operation of the loaded camera After sealing the Case, check that the camera operations normally. 1 Push the ON/OFF button on the Case and confirm that the camera turns ON/OFF. 2 Press the shutter lever on the Case and confirm that the camera shutter releases. [. . . ] Perform at the location without sand or dust, after washing and drying your hands. En Remove the O-ring 1 Insert the O-ring remover between the O-ring and the O-ring groove. 2 Slip the tip of the inserted O-ring remover below the O-ring. (Be careful not to scratch the O-ring groove with the tip of the O-ring remover. ) 3 Hold the O-ring with your fingertips after it has come out of the groove and remove it from the Case. Remove any sand, dirt, etc. After visually checking that dirt has been removed from the O-ring, checks for sand and other foreign matter adhered, damage and cracks can be done by squeezing the entire circumference of the O-ring lightly with your fingertips. EN 24 Remove any foreign matter adhered to the O-ring groove using a lint-free clean cloth or cotton swab. Also remove any sand or dirt adhered to the O-ring contact surface on the front lid of the case. En CAUTION: · Maintenance of the waterproof functions is required even before using this product underwater for the first time. [. . . ]