User manual PYRAMID PW855US-X DATASHEET

[. . . ] Before use, perform an advance check as described in this manual. Introduction Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from improper use of this product. Please read the following items before use This Case is a precision device designed for use at a water depth within 40 m. Please use the Case correctly after sufficient understanding of the contents of this manual in regard to handling of the Case, checks before use, maintenance, and storage after use. [. . . ] 22 Locking AF during underwater shooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handling After Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Wipe off any waterdrop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Take out the digital camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Wash the Case with pure water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Dry the Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintaining the Waterproof Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Remove the O-ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 EN 6 How to Apply Grease to the O-ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Install the O-ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Replace consumable parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 7. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Turn the mode dial on the Case and confirm that the camera mode switches properly. · Check if the correct mode is being switched from the LCD monitor. 3 Press the shutter lever on the Case and confirm that the camera shutter releases. · Also operate other control buttons on the Case and confirm that the camera functions properly. EN 18 Perform the final checks Visual Inspection After sealing the Case, check the sealing part of front and rear lid visually to confirm that the O-ring is not twisted or out of the groove and that no foreign matter has been caught. Also check that the Case is not broken or cracked. CAUTION: Hairs, fibers, and other narrow items are not very apparent, but they may cause water leakage. In addition, pay special attention to breaks and cracks on the Case. En EN 19 Water Leakage Test The final test after loading the camera is explained below. It can be performed easily in a water tank or a bathtub. The required time is about five minutes. En 1 Simple water leakage test Place the Case slowly into the water. Explanatory image Hints As the Case is transparent, waterdrops entering into it can be confirmed easily. In case of trouble with the O-ring, three seconds are enough for water to enter. Are there air bubbles coming out between the lids? [. . . ] Perform at the location without sand or dust, after washing and drying your hands. En Remove the O-ring 1 Insert the O-ring remover between the O-ring and the O-ring groove. 2 Slip the tip of the inserted O-ring remover below the O-ring. (Be careful not to scratch the O-ring groove with the tip of the O-ring remover. ) 3 Hold the O-ring with your fingertips after it has come out of the groove and remove it from the Case. Remove any sand, dirt, etc. After visually checking that dirt has been removed from the O-ring, checks for sand and other foreign matter adhered, damage and cracks can be done by squeezing the entire circumference of the O-ring lightly with your fingertips. EN 25 Remove any foreign matter adhered to the O-ring groove using a lint-free clean cloth or cotton swab. Also remove any sand or dirt adhered to the O-ring contact surface on the front lid of the case. En CAUTION: · Maintenance of the waterproof functions is required even before using this product underwater for the first time. [. . . ]