User manual PYRAMID XPA-240 AMPLIFIER

[. . . ] 15 Power Amplifier XPA-240 Amplifier XPA-360 Amplifier XPA-480 Amplifier www. pyramidcaraudio. com TABLE OF CONTENTS INSTALLATION GUIDELINES Connecting the GND (Ground) screw terminal Connecting a mixer or preamplifier may cause excessive noise or hum in the amplifier output. To prevent this, connect one end of a low-capacitance shielded wire to the amplifier's ground screw (on the rear panel). [. . . ] Installed properly, you can expect years of trouble-free service from this product. Input connections These amplifiers accept a broad range of input sources, including Compact Disc (CD) players; DVD, Cassette, Reelto-Reel or other tape players; Radio Tuners; Equalizers; Signal Processors. FEATURES AND CONTROLS Channel 1 and Channel 2 Power LED Display Indicate the output signal level for each channel. BAL ANCE D I NPUT S HOT(+) COLD(-) GND Connecting a CD or DVD or tape player or tuner In a normal installation, one would use the RCA JACKS for connecting a CD player, DVD, tape player or tuner. FRONT PANEL, XPA-240. XPA-360. XPA-480 INPUTS OUTPUTS CH-2 BRIDGE CH-1 STEREO BRIDGE MONO NOTE: Use 16-gauge speaker wire for lengths up to25 feet; 14-gauge wire for lengths over 25 feet. It is recommended that you use the shortest length of wire possible. VOLTAGE POWER CONSUMPTION : 500 W ~AC iN 115/230V-60/50 Hz CH-2 CH-1 CH-1 +3 CH-2 LIFT 0 -5 -10 -15 -20 -30 -30 -20 -15 -10 -5 0 +3 GND GROUND LIFT 2. Connect the speaker wires to the speaker's positive and negative terminals. FUSE CHANNEL 1 CHANNEL 2 POWER ON OFF PROTECT MIN MAX MIN MAX 2000 Watt Power Amplifier use RCA jacks CD PLAYER, DVD , TAPE PLAYER OR TUNER NOTE: Most speaker terminals are either color-coded or have a mark that indicates the terminal's polarity. Usually positive terminals are red or have a plus symbol (+), and negative terminals are black or have a minus symbol (-). Connect the speaker wires to the amplifier's left and right speaker terminals according to the terminal color polarity. Power On/Off Connecting an equalizer or external signal processor Connect the processor's OUT to the amplifier's INPUT connectors. EQ OR MIXER Channel 1 and Channel 2 Output Level Controls Lets you adjust the sound levels for each channel. Protection Circuit and Indicator The indicator will be illuminated when the amplifier is powered on and at turnon delay status; the indicator will be turned off after internal outputs are connected. The indicator will also be illuminated when the amplifier has abnormal problems, such as overload or excessive heat. STEREO OPERATION SWITCH IN "STEREO" POSITION Fan Cooling Cooling system is automatically activated whenever amplifier is turned on. This forced air cooling system rapidly exhausts interior heat, reducing operating temperature and aiding performance. REAR PANEL, XPA-240. XPA-360. XPA-480 BAL ANCE D I NPUT S HOT(+) COLD(-) GND -OR­ INPUTS CH-2 CH-1 CH-1 STEREO MONO BRIDGE OUTPUTS CH-2 BRIDGE VOLTAGE POWER CONSUMPTION : 500 W CH-1 ~AC iN 115/230V-60/50 Hz CH 2 GND CH-2 B A LA N C ED I N P U TS CH 1 GROUND LIFT BAL A NCE D I N PUT S HOT(+) COLD(-) GND INPUTS OUTPUTS POWER CONSUMPTION : 500 W ~AC iN 115/230V-60/50 Hz HOT(+) COLD(-) GND VOLTAGE LIFT FUSE INPUTS CH-2 CH-1 CH-1 STEREO MONO BRIDGE OUTPUTS CH-2 BRIDGE VOLTAGE POWER CONSUMPTION : 500 W CH-2 BRIDGE CH-1 CH-2 CH-1 CH-1 ~AC iN 115/230V-60/50 Hz CH-1 MONO GND CH-2 GROUND LIFT STEREO BRIDGE LIFT FUSE GND GROUND LIFT CH-2 LIFT FUSE EQ OR MIXER STEREO SIGNAL SOURCE use XLR/6. 35 mm combo jacks Input Jacks Let you connect a variety of audio input sources via the balanced (XLR/6. 35mm phone jack combinations) or unbalanced (RCA) inputs. Stereo/Mono Switch Lets you select conventional stereo operation with a stereo input signal or bridged mono input mode. CAUTION!Do not use balanced and unbalanced inputs simultaneously!! 1-PYRAMID XPA-240/XPA-360/XPA-480 Amplifier Owner's Manual PYRAMID XPA-240/XPA-360/XPA-480 Amplifier Owner's Manual ­ 2 Amplifier Specifications Input Impedance, balanced (unbalanced) Continuous Output Power Stereo Mode Mounting the amplifier This amplifier is designed to accept standard rack mounting installations. Two slots on each end of the front panel make it suitable for such an installation. [. . . ] When this occurs, you should simply reduce the output power level by rotating the Master Volume control counterclockwise. HOT(+) COLD(-) GND INPUTS OUTPUTS VOLTAGE POWER CONSUMPTION : 500 W CH-2 CH-1 CH-2 CH-1 ~AC iN 115/230V-60/50 Hz BRIDGE CH-1 MONO STEREO BRIDGE GND GROUND LIFT CH-2 LIFT FUSE USE CHANNEL 1 INPUT ONLY MONO SIGNAL SOURCE CAUTION!Do not use balanced and unbalanced inputs simultaneously!! PYRAMID XPA-240/XPA-360/XPA-480 Amplifier Owner's Manual-4 3-PYRAMID XPA-240/XPA-360/XPA-480 Amplifier Owner's Manual [. . . ]