User manual QSC AUDIO WL218-SW & ACCESSORIES

[. . . ] This warranty gives you specific legal rights. This limited warranty is freely transferable during the term of the warranty period. Customer may have additional rights, which vary from state to state. In the event that this product was manufactured for export and sale outside of the United States or its territories, then this limited warranty shall not apply. [. . . ] ·Be absolutely certain of the integrity of any structural member intended to support suspended loads. Hidden structural members can have hidden structural weakness. ·Consult a Professional Mechanical or Structural Engineer licensed in the jurisdiction of the sound system installation to review, verify, and approve all attachments to the building or structure. ·Never assume anything- Owner or third-party supplied suspension attachment points may not be adequate for the loads to be suspended. ·Employ the services of a Professional Rigger for hoisting, positioning, and attaching the equipment to the supporting structure. ·Always inspect all components (enclosures, suspension brackets, pins, frames, bolts, nuts, slings, shackles, etc. ) for cracks, wear, deformation, corrosion, missing, loose, or damaged parts that could reduce the strength of the assembly before lifting. Discard any worn, defective, or suspect parts and replace them with new appropriately load-rated parts. Shock Loading When a load is either moved or stopped, its static weight is magnified. Sudden movements can magnify the static weight several times. This magnification of static weight is termed "shock loading". Shock loading poses a danger to equipment and workers. The effects of shock loading can be instantaneous, or they may remain undetected unless the equipment is visually damaged. Avoiding shock loading requires careful planning and knowledge of equipment, rigging, and lifting practices. Shock loading of equipment and structures is usually confined to lifting and installation, but natural forces (winds, earthquakes) can impose shock loads several times the static load. This is why structures and suspension equipment must be capable of supporting several times the weight of the equipment suspended. WideLine Working Load Limits and Design Factors Table 1 lists the WideLine suspension components and provides Working Load Limit data at various Design Factors. The tabulated Design Factors are for static loads only. The choice of which Design Factor to use will depend upon the jurisdiction and venue of installation, as well as the conditions of suspension. Dynamic conditions are determined by unknown, installation-specific factors and should be referred to a Licensed Structural Engineer for clarification before proceeding with any suspension of the equipment. The data presented is based upon the listed component weights: Table 1: WideLine WL218-sw System Working Load Limits Component WL218-sw Loudspeaker AF218-sw Array Frame 1/2-inch Shoulder Bolt1 5/16-inch Ball Lock Pin1 1/2-inch Ball Lock Pin1 Weight 206 lb (93. 4 kg) 80 lb (36. 3 kg) n/a n/a n/a 5:1 Design Factor 3400 lb(1540 kg) 3400 lb(1540 kg) 6400 lb (2900 kg) 2400 lb (1090 kg) 6400 lb (2900 kg) 7:1 Design Factor 2400 lb (1090 kg) 2400 lb (1090 kg) 4500 lb (2040 kg) 1700 lb (771 kg) 4500 lb (2040 kg) 10:1 Design Factor 1700 lb (771 kg) 1700 lb (771 kg) 3200 lb (1450 kg) 1200 lb (544 kg) 3200 lb (1450 kg) 1- Working Load Limits are per fastener loaded in double shear. Data is for informational purposes only. 5 Rigging (continued) NOTE: All hardware/components must be rated for the expected loads as determined by the Professional Engineer responsible for suspension. Front Articulated Joint1- Remove the ball lock pin. 2- Slide the articulated joint out of the receiver tube by lifting its retaining screw upward. 3- Lock in place using the ball lock pin. 1 Attaching WL218-sw Loudspeaker to WL218-sw Loudspeaker 1- With the enclosures on dolly boards and facing downward, position two enclosures adjacent one another such that the front receiver tubes are aligned. 2- Unpin and extend the articulated joints from the lower enclosure. [. . . ] This accommodates using one input cable assembly (where appropriate) for subwoofer and full range loudspeaker connections. Additionally, pin numbers 1+ and 1- of both NL4s are wired in parallel. The WL218-sw loudspeaker is not equipped with a crossover network. All signal processing must be done before connecting audio power to the loudspeaker. INPUT/OUTPUT WORKING 3400 LBS / 2430 LBS / 1700 LBS / 771 WEIGHT 206 LBS PIN 1+ 2+ QSC AUDIO PRODUCTS, LLC COSTA MESA CALIFORNIA, MADE IN USA Reconfiguring the Input Connections for Separate Transducer Connection If separate transducer connection is required, the input plate may be removed and the wiring altered so that each transducer has a separate, dedicated connection. [. . . ]