User manual QUAD C8 REV 1

[. . . ] UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUSPEND OR OTHERWISE MOUNT THIS EQUIPMENT UNLESS YOU ARE FULLY QUALIFIED AND CERTIFIED TO DO SO BY RELEVANT LOCAL, STATE AND NATIONAL AUTHORITIES. ALL RELEVANT SAFETY REGULATIONS MUST BE FOLLOWED. [. . . ] Speakers are packed in pairs and come complete with a tile backing C-ring, mounting support rails plastic paint covers and cardboard cutout templates. · Concourse C6 ­ Selectable 4/16/70V/100V operation, 50W transformer included PRODUCT FEATURES All models include the following components: · Speaker assembly (2) · Cover grille with restraint (2) · Split C ring backing plate (2) · Support Rails (4) · Plastic paint cover (2) · Cardboard cutout template (2) Please ensure that you are familiar with all of the parts and how they are assembled before commencing the installation. GRILLE POWER TAP SWITCH HF DRIVER GRILLE TETHER LF DRIVER BEZEL PRODUCT DESCRIPTIO N Concourse C models are complete assemblies ready for installation into both suspended tile ceilings and hard ceilings. A rear mounted terminal box allows termination of the speaker wiring to the speaker as well as impedance selection (except C4T and C4-16). Power taps are selected on 70/100V versions through a front mounted rotary switch. Speakers are mounted by means of four mounting clamps located around the rear face of the bezel. A metal split C ring is provided to distribute the clamping pressure evenly along the ceiling surface. A pair of metal mounting support rails are provided for added support when the speakers are installed in a suspended tile ceiling. A seismic restraint point is provided on the rear of the speaker to facilitate attachment of a restraint tether to the building's structure. The removable front grille is also fitted with a restraint tether that attaches to the inside of the bezel by means of a supplied insert. INPUT TERMINALS IMPEDANCE SELECT SWITCH BACKBOX SEISMIC RESTRAINT POINT MOUNTING CLAMPS SPLIT C RING MOUNTING CLAMPS SUPPORT RAILS Concourse C4, C4-8, C4-16, C4-T 252mm/9. 92" 212mm/8. 35" Concourse C6 295mm/11. 61" 212mm/10. 04" 219mm/8. 62" Concourse C8 333mm/13. 11" 293mm/11. 54" 219mm/8. 62" Concourse CSUB 371mm/14. 6" 331mm/13. 03" 238mm/9. 37" 6 349mm/13. 74" INSTALLATION Suspended Tile Ceilin g s Step 1 Carefully unpack the contents of the box and ensure that all parts are accounted for before beginning installation. STEP 3 Step Remove the tile from the ceiling and place it on a suitable work surface to cut the hole and assemble the speaker. Locate the cardboard mounting template and use it to mark the hole size needed for the installation. Center the template on the ceiling tile and cut the hole using a suitable saw, or knife. Step Once the hole is cut, rest the speaker face-down on the work surface and place the cut ceiling tile over top of the assembly, ensuring the tile is resting on the speaker bezel. Step Place the mounting rails on the ceiling tile on either side of the speaker assembly ensuring that they are oriented correctly to provide support by resting on the tile mounting grid when installed in the ceiling STEP 6 Step Place the C ring over top of the speaker assembly and align it with the mounting rails. Using the supplied screws, fasten the C ring to the mounting rails. Step 6 Lift the assembly to gain access to the front of the speaker, then using a screwdriver tighten each of the four mounting screws in sequence. Turning the screws in a clockwise direction will cause the mounting clamps to rotate into position then extend down to clamp the assembly to the ceiling tile. Step Remove the screws holding the terminal cover plate and then remove any knock outs needed to connect the speaker wiring. STEP 9 Step 8 Select the appropriate impedance using the push-button switch inside the terminal box if the speaker is part of a low impedance system (except C4T and C4-16). Step 9 Lift the entire assembly to the ceiling and terminate the wiring to the terminal strip. Replace the cover plate and screws. Step 10 Place the assembled speaker and ceiling tile into the ceiling grid, ensuring that the mounting rails are resting correctly on the grid. Step 11 Set the correct wattage tap (except C4-16) using the front mounted rotary power switch. [. . . ] 6" Cone ø 1" Soft Dome Tweeter Tweeter 2. 5kHz Plastic (ABS) metal can Screw Terminal 11. 61" x 8. 62" 295 x 219mm 4. 1kg 9. 02lbs. 8" Cone ø 1" Soft Dome Tweeter 2. 3kHz Plastic (ABS) metal can Screw Terminal 13. 11" x 9. 37" 333 x 238mm 5. 3kg. [. . . ]