Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual QUANTUM ATL P2000. We hope that this QUANTUM ATL P2000 user guide will be useful to you.
Lastmanuals help download the user guide QUANTUM ATL P2000.
Manual abstract: user guide QUANTUM ATL P2000V2 REL 0
Detailed instructions for use are in the User's Guide.
[. . . ] ATL P2000 Series Automated Tape Library
User's Guide
6316800-02
Ver. 0
ATL P2000 Series Automated Tape Library User's Guide, 6316800-02, Ver. provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. may revise this publication from time to time without notice. [. . . ] Take electrostatic discharge precautions as explained in Taking ESD Precautions on page 18. Using the key from the accessories kit, unlock the front door. Lift the door handle straight up and then turn the handle counterclockwise to unlatch the door. Gently pull on the door handle to open the door.
b
c
d
e
f 2
Press the Unload button on the drive (see figure 24). When you press Unload, the tape cartridge rewinds. This may take between 10 to 120 seconds. When the rewind process is completed, the Operate Handle indicator comes on.
Figure 24 DLT Tape Drive Front Bezel (Example)
Unload button
Insert/release handle (shown in up position)
42
ATL P2000 Series Automated Tape Library User's Guide
Chapter 2 Basic Library Operations Manually Ejecting a Tape Cartridge
3
When the Operate Handle indicator comes on, raise the insert/ release handle to eject the tape cartridge. Note: Place your finger approximately 1/4 of an inch in front of the drive's cartridge opening to ensure that the cartridge does not drop when ejected. Caution: Pause for at least 3 seconds, then grasp the tape cartridge and slowly pull it half way out of the drive. Caution: If the tape cartridge leader failed to detach from the take-up leader, push the tape cartridge all of the way back into the drive, press down the insert/release handle, and return to step 2. Otherwise, continue to step 5.
4 5
Pull the tape cartridge completely out of the drive. Close and lock the library door.
Quantun SDLT and IBM Ultrium LTO Tape Drives 2
To manually eject a tape cartridge from Quantum SDLT or IBM Ultrium LTO T200 tape drives:
1 2
Refer to Steps 1a-1f under DLT Tape Drives on page 42. The Unload button works the same as a soft eject (VCR-style) button.
ATL P2000 Series Automated Tape Library User's Guide
43
Chapter 2 Basic Library Operations Manually Ejecting a Tape Cartridge
44
ATL P2000 Series Automated Tape Library User's Guide
Chapter 3
Operator Commands
3
This chapter describes the commands found on the Operator screen of the touch screen GUI. The Operator screen commands initiate the following actions: · · · · · · · Opening the Operator screen Unloading the load port Configuring the library* Configuring library options* Performing an inventory* Moving cartridges* Unloading a drive*
* The library must be off-line to perform these functions
Caution: Library operator commands are to be used only by qualified, ATL-trained personnel. Serious operational problems and data loss may occur if you do not understand the consequences of these commands.
ATL P2000 Series Automated Tape Library User's Guide
45
Chapter 3 Operator Commands Opening the Operator Screen
Opening the Operator Screen
To open the Operator screen:
1
3
Press the Operator tab. The GUI displays the password screen (see figure 25).
2
Enter the correct operator password to gain access to the Operator screen (see figure 26). Note: To change passwords, see Press Continue. A "Command in Progress" dialog box is displayed. on page 66
Figure 25 Password Screen
PRODUCTS
Back
Forward Tapes
Home Service 1 3 2 4 6 8 0
ATL
System Off-line
Operator Enter Password
Standby Load Port 5 Enter Password: _ 7 9
O
Stop Enter
46
ATL P2000 Series Automated Tape Library User's Guide
Chapter 3 Operator Commands Configuring the Library
Figure 26 Operator Screen
PRODUCTS
ATL
System Off-line
Back Overview Config.
Forward Tapes
Home Operator
Control
Standby Load Port
Configure Library
Move Cartridges
Calibrate Library
Unload Drive
O
Stop
Configure Options
Inventory Tapes
Unload Imp/Exp
Configuring the Library
The Configure Library command allows you to assign the following: · · · · · Library model number Number of storage bins Number of drives Library SCSI ID Tape drive SCSI ID
3
To configure any of these attributes:
1
In the Operator screen, press the Configure Library button. The GUI displays the Library screen (see figure 27).
ATL P2000 Series Automated Tape Library User's Guide
47
Chapter 3 Operator Commands Configuring the Library
Figure 27 Configure: Library Settings Screen
PRODUCTS
ATL
System Off-line
Back Overview Configure: Library Inquiry: Model: Serial Number: IEEE ID: # Bins: # Drives: Library SCSI ID: Drive 0 SCSI ID: Drive 1 SCSI ID: Drive 2 SCSI ID:
Forward Tapes
Home Operator
Standby Load Port
P2000 6318250 6318250
O
Stop
198 8 0 2 3 4
Configure
2
Press the Configure button. The GUI dispays the Configure: Library Settings screen (see figure 28).
Figure 28 Configure: Library Settings Screen
Back Overview System Off-line Standby Load Port #Drives: PTMs: O Device:
Forward Tapes
Home Operator Service
Configure: Library Settings Model: # Bins: 6318050 192 10 0 Library Change Select
Stop
SCSI ID: 0
48
ATL P2000 Series Automated Tape Library User's Guide
Chapter 3 Operator Commands Configuring Library Options
3
Press the Select button until you highlight the setting you want to change. Using the arrow buttons, scroll through available values for the setting. [. . . ] LVD SCSI cabling requires "Twist and Flat" ribbon cable and an LVD/SE terminator or a "Twist and Flat" ribbon cable with built-in LVD termination. All IBM LTO tape drives are LVD devices. Quantum DLT8000 and SDLT tape drives can be LVD or HVD devices. M
This term refers to the use of different tape drive types within one tape library. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE QUANTUM ATL P2000
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual QUANTUM ATL P2000 will begin.