User manual QUANTUM DAT72 81-81396-01 A01

[. . . ] DDS-4/DAT 72 User's Guide, 81-81396-01 A01, November 2005. DAT 72 SCSI Internal Tape Drive (part number CD72LWH) DAT 72 SCSI External Tape Drive (part number CD72LWE) DAT 72 SATA Internal Tape Drive (part number CD72SH) Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. COPYRIGHT STATEMENT Copyright 2005 by Quantum Corporation. [. . . ] Note: The SATA vendor ID is QUANTUM DAT. Recording Drive Information After you review and, if necessary, change the drive's default settings, record the drive information. That way, you can reference this information in the future, without having to gain access to the drive inside your computer. 2 Accessing the Inside of Your Computer To gain access to the inside of your computer: 1 Shut down the computer as you would normally. Then turn off the computer and all peripherals connected to it. 2 Remove the computer's power cord from the computer's AC connector. 2 DDS-4/DAT 72 User's Guide 24 Chapter 2 Installing Internal Tape Drives Mounting the Internal Tape Drive 3 Remove the computer cover to gain access to the inside of the computer. The documentation that came with your computer should explain this procedure. Note: If you have to disconnect cables to gain access to the mounting bay, note which cables were removed. You can then refer to this information when you reconnect the cables at the end of this procedure. 4 Select an available 3. 5-inch or 5. 25-inch mounting bay, depending on the internal tape drive you want to install. Note: The internal tape drive can be mounted horizontally or vertically (on its side). 5 If the mounting bay has a "filler panel, " remove it according to the instructions in your computer's documentation. 6 If the computer does not have a SCSI host adapter, you will need to purchase and install a SCSI host adapter. Mounting the Internal Tape Drive 2 An internal tape drive without mounting brackets can be installed into a 3. 5-inch drive bay. An internal tape drive with mounting brackets can be installed into a 5. 25-inch drive bay. · To mount the internal tape drive into a 3. 5-inch bay, see Mounting the Drive into a 3. 5-inch Drive Bay. · To mount the internal tape drive into a 5. 25-inch bay, see Mounting the Drive into a 5. 25-inch Drive Bay. Mounting the Drive into a 3. 5-inch Drive Bay 2 drive bay. This procedure assumes your drive is not equipped with sidemounting brackets. The following procedure describes how to mount the drive in a 3. 5-inch DDS-4/DAT 72 User's Guide 25 Chapter 2 Installing Internal Tape Drives Mounting the Internal Tape Drive 1 Orient the drive so the front of the drive faces the front of the computer. 2 Insert the drive into the computer's drive bay. 3 Align the drive's front panel with the front panel of the computer. Secure the drive in the mounting bay using two M3. 0 metric screws on each side of the drive (see figure 5). Figure 6 shows, the 5. 25-inch drive has four screw holes on the bottom and five on each side. Warning: Do not use screws longer than 4 mm; otherwise, you may damage the drive. 4 Proceed to Connecting a SCSI Cable. Figure 5 Mounting an Internal Tape Drive DDS-4/DAT 72 User's Guide 26 Chapter 2 Installing Internal Tape Drives Mounting the Internal Tape Drive Figure 6 Mounting Holes for the Internal Tape Drive in a 3. 5-inch Installation 41. 3 mm (1. 63 in) 13. 0 mm (0. 51 in) 2 places 5. 0 mm (0. 196 in) 2 places 101. 6 mm (4. 00 in) 3. 8 mm (0. 15 in) 94. 0 mm (3. 70 in) M3. 0 x 4 deep min. (10 places) 90. 0 mm (3. 54 in) 2 places 60. 0 mm (2. 36 in) 2 places M3. 0 x 4 deep min. (4 places) 146. 0 mm (5. 75 in) 70. 0 mm (2. 75 in) 21. 0 mm (0. 83 in) 2 places 31. 0 mm (1. 22 in) 41. 2 mm (1. 62 in) 6. 0 mm (0. 24 in) 101. 6 mm (4. 00 in) Side View Note: Tolerance for all dimensions is 0. 25mm (0. 01 in) Bottom View Mounting the Drive into a 5. 25-inch Drive Bay 2 The following procedure describes how to mount the drive in a 5. 25-inch drive bay. This procedure assumes your drive has mounting brackets on the sides. 1 Orient the drive so the front of the drive faces the front of the computer. [. . . ] If the front panel LEDs are flashing together, contact the Technical Support department. If the Drive LED is flashing rapidly during drive operation: 1 Press the Eject button to remove the tape. 2 If the tape does not eject within 2 minutes, press and hold the Eject button for more than 5 seconds. The tape should eject within 40 seconds. [. . . ]