User manual QUANTUM DLT1IRIX536X

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual QUANTUM DLT1IRIX536X. We hope that this QUANTUM DLT1IRIX536X user guide will be useful to you.

Lastmanuals help download the user guide QUANTUM DLT1IRIX536X.


Mode d'emploi QUANTUM DLT1IRIX536X
Download
Manual abstract: user guide QUANTUM DLT1IRIX536X

Detailed instructions for use are in the User's Guide.

[. . . ] DLTTM TAPE UNIT INSTALLATION SGI® Systems IRIX® 5. 3 and 6. X Installation SGI system must have the appropriate SCSI interface for DLT drive to attached to, i. e. , a SCSI singleended DLT drive can be attached only to a SCSI single-ended interface. The same is true for SCSI differential attachment. [. . . ] As appropriate for the currently running operating system version, add the following to the table of structures. This will enable DLT system recognition: For IRIX 5. 3: /* DLT tape drive */ {DECDLT, TPDLT, "<Vendor length>", 7, "<Vendor ID>", "<DLT tape unit>", 0 , 0, {0, 0, 0, 0 }, MTCAN_BSF | MTCAN_BSR | MTCAN_APPEND | MTCAN_SPEOD | MTCAN_CHKRDY | MTCAN_VAR | MTCAN_SETSZ | MTCAN_SILI | MTCAN_SEEK | MTCAN_SYNC | MTCAN_CHTYPEANY, 20, 8*60, 20*60, 5*60, 16384, 64*1024} For IRIX 6. X: /* DLT tape drive */ {DECDLT, TPDLT, "<Vendor length>", 7, "<Vendor ID>", "<DLT tape u nit>", 0 , 0, {0, 0, 0, 0 }, MTCAN_BSF | MTCAN_BSR | MTCAN_APPEND | MTCAN_SPEOD | MTCAN_CHKRDY | MTCAN_VAR | MTCAN_SETSZ | MTCAN_SILI | MTCAN_SEEK | MTCAN_SYNC | MTCAN_CHTYPEANY, 20, 8*60, 20*60, 5*60, 16384, 64*1024, 0 (u_char *)0} Depending on the DLT tape peripheral you are installing, you will need to make substitutions for <Vendor length>, <Vendor ID>, and <DLT tape unit> in the above structure. The following table shows the DLT tape product and the corresponding substitution values: <Vendor length> <DLT tape unit> DLT Tape Product <Vendor ID> DLT1 7 BNCHMARK DLT1 Keep in mind that the Vendor ID entries are case sensitive. Refer to the tpsc_types structure in the /usr/include/sys/tpsc. h file for further information on the above structure entries and to the /usr/include/sys/mtio. h file for further information on the MTCAN flag definitions. 1. Enter the following command to configure the DLT device into the system: /etc/autoconfig 1. After reboot is complete and you have logged in as root, change directory to /dev. Enter the following command to establish the DLT device files: . /MAKEDEV 1. Verify the DLT device files by entering the following command: ls /dev/rmt For a DLT tape peripheral installed with a SCSI ID of 4, the system response should be similar to the following: tps0d4 tps0d4c tps0d4nr tps0d4nrc tps0d4nrnsc tps0d4nrnsv tps0d4nrs tp s0d4nrsv tps0d4nsc tps0d4stat tps0d4sv tps0d4v tps0d4vc tps0d4nrsvc tps0d4nsv tps0d4nrvc tps0d4ns tps0d4s tps0d4sc tps0d4nrnsvc tps0d4nrv tps0d4nsvc tps0d4svc tps0d4nrns tps0d4nrsc 1. Enter the following command to verify the installation: mt -t /dev/rmt/tps0d4 status Note that the device file tps0d4 is for an installed DLT1 with SCSI ID of 4. The system response should be similar to the following: Controller: SCSI Device: BNCHMARK: DLT1 Status: 0x 20262 Drive type: DLT Media : READY, writeable, at BOT DLT Tape Drive Use and IRIX Behavior During periods of non-use of the DLT tape drive there is a danger of unintended overwriting of previously written data. Also, rewinding of DLT tape may occur before the next record is read when the intent is to read the next record at the current tape position. The cause of this behavior is that the IRIX tape driver unloads from system memory after approximately five minutes of non-use of the tape drive. A reload of the driver will occur when a command to access the tape drive is requested. During driver reload, certain initialization tasks occur and one of these tasks is to load a tape cartridge into the drive. [. . . ] Therefore, an installed DLT7 mini-library can not be utilized in random access mode and can only be accessed in sequential mode. Refer to the DLT1/DLT7 Install and Operations Guide product manual for detailed description of these access modes. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE QUANTUM DLT1IRIX536X

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual QUANTUM DLT1IRIX536X will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag