Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual QUANTUM DPM5500. We hope that this QUANTUM DPM5500 user guide will be useful to you.
Lastmanuals help download the user guide QUANTUM DPM5500.
You may also download the following manuals related to this product:
QUANTUM DPM5500 (1843 ko)
Manual abstract: user guide QUANTUM DPM5500
Detailed instructions for use are in the User's Guide.
[. . . ] It is important to the chassis installation to locate the hole pattern in the rack rails (see figure 2).
Figure 2 Rail Hole Pattern
Clip nut
5U of rack space
5U
1 DPM5500 System (5U) 1U = 1. 75 in (44. 45mm)
Installing the DPM5500 Chassis
0
1 Assemble the DPM5500 rack rails as shown in figure 3. You must pull the slide out of the support brackets to gain access to the mounting holes.
The marks above (X) indicate the location of mounting hardware on the rack rails. Ensure that any necessary mounting hardware is installed on the rack rails prior to installing the chassis.
Hole pattern Top of rack . 312 in (7. 92 mm) . 625 in (15. 9 mm) . 625 in (15. 9 mm) . 5 in (12. 7 mm) . 625 in (15. 9 mm) . 625 in (15. 9 mm) . 5 in (12. 7 mm)
Figure 3 Assembling the Rack Rails DPM5500: Front mounting bracket preset. Ensure the screws are in the correct position.
WARNING: If the rack is empty at the time of installation, do NOT install the DPM5500 chassis too high in the rack. [. . . ] Refer to the label on the bottom of the drive sled for the drive number. The hard drives must also be installed in the array in which it was configured.
Drive 8 Array controller 2 Drive 4 Drive 0 Drive 8 Array controller 1 Drive 4 DPM5500 Drive 0 Drive 9 Drive 5 Drive 1 Drive 9 Drive 5 Drive 1 Drive 10 Drive 11 Drive 6 Drive 2 Drive 7 Drive 3
Figure 8 DPM5500 System Cabling
Ethernet cables (ports 1 and 2)
Drive 10 Drive 11 Drive 6 Drive 2 Drive 7 Drive 3
12
Power supply cables
5
DPM5500 Quick Start Guide
DPM5500 Default Configuration
0
DPM5500 Initial Configuration
To initially configure the DPM5500 and prepare for operation: NOTE: A domain server must be setup and on the same network as the DPM5500 before continuing with this procedure. NOTE: It is highly recommended that the system administrator with access to the DHCP server be available during this initial configuration of the DPM5500. The IP address assigned to the DPM5500 must available to access the system. 1 Turn on the DPM5500 system by pressing the power button located on the front of the chassis.
0
The DPM5500 is configured from Quantum with Microsoft Windows Server 2003 and Data Protection Manager loaded on the device. The DPM5500 contains a system motherboard, processor, and a SCSI HBA. Refer to the following username and password to access the system:
Username: administrator Password: Quantum-DPM
NOTE: The password is case sensitive. NOTE: It is recommended to join a test domain within Windows
0
0
The storage array portion of the DPM5500 system contains 12, 18, or 24 hard drives and is used as the primary storage area of the DPM5500. The DPM application, SQL DPM database, and the Windows 2003 operating system are located on 2 internal mirrored hard drives. The DPM5500 is formatted from Quantum with the following partition: · · 37 GB Partitions Storage Area
2 The DPM5500 uses DHCP (Dynamic Host Configuration Protocol) to receive an IP address from a local DHCP server. You will need this IP address to access the DPM5500. Write the IP address in the space provided below: DPM5500 IP Address:___________________________ Example: https://<ip address>:8098 NOTE: This IP address uses https, not the common http and there is also a special port (8098) that must be used. This address must be used every time the web pages are accessed. 3 Enter the IP address assigned to the DPM5500 into a web browser to access the DPM5500 configuration wizard. The DPM5500 configuration wizard displays (see figure 9).
37 GB Partitions
The operating system hard drives contain a single 37 GB partition. This partition contains the Windows Server 2003 operating system which serves as the boot partition. This partition also contains the DPM application software and DPM application database.
0
Storage Area
0
The storage area contains a 4. 8 TB, 7. 2 TB, or 9. 6 TB (approx. ) partition for use as storage space for the DPM software. This partition is only used by DPM and is not accessible from the Windows Server 2003 operating system.
Microsoft® DPM
0
The Microsoft® DPM application software is installed on the system, however, the software is not initially configured. [. . . ] 8 Re-enter the DPM5500 IP address in the web browser to access the configuration wizard. 9 Click the Start Wizard link to continue the configuration wizard. The Date and Time Configuration screen displays (see figure 13).
Figure 14 Server Identity Configuration
11 Enter the following server identity information: · Server name or accept the system generated server name. This name must be unique from any other DPM5500 systems on the same network. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE QUANTUM DPM5500
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual QUANTUM DPM5500 will begin.