User manual QUANTUM FASTSTOR 1 QUICK INSTALLATION GUIDE

[. . . ] Trademarked names are used solely for identification or exemplary purposes, and any omissions are unintentional. ADIC is a registered trademark and of Advanced Digital Information Corporation. Published: October 2005 Document Number: 6-01497-01 Rev A Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking the FastStor 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the FastStor 1 in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: Using more than two screws will increase the stability of the Rack Mounting Kit. Place the "Rail Left Assembly" on the left side of the rack, between the rear rack mount rail and the front rack mount rail. Mount the "Rail Left Assembly" at the desired height using one M6x12 screw in front (upper hole in rail only) and two M6x12 screws at the back. See Figure 5. Installing the "Rail Right Assembly" Follow the instruction for left side only using the "Rail Right Assembly" on the right side of the rack. Rear Rack Mount Rail Step 5 (Screw M6x12) Use these holes if rack depth is equal to or longer than the FastStor 1 Step 1 Use these holes if rack depth is shorter than the FastStor 1 Step 1 Step 3 (Screw M4x12, nut and washer) Front Rack Mount Rail Step 2 Step 5 (Screw M6x12) Figure 4. Mounting the Rack mounting kit to a rack FastStor 1 Quick Installation Guide 5 Advanced Digital Information Corporation FastStor 1 Figure 5 shows step 5 in the description: Rack mounting kit mounted in rack with one screw M6x12 in upper hole on both left and right sides. On the rear side, two screws must be used on both left and right sides. A total of six screws are used to install the rack mounting kit to the rack. Figure 5. Rack mounting kit mounted in rack Mounting the FastStor 1 to the Rack Make sure all screws in the Rack Mounting Kit are tightened properly before installing the FastStor 1 in the rack. Slide the FastStor 1 on the rails from the front of the rack, as shown in Figure 6. Then secure the FastStor 1 using one M6x12 screw in front of the rack on both left and right sides (see Figure 7), and one M5x8 on the back of the Rack Mounting Kit on both left and right sides (see Figure 8). Figure 6. Slide the FastStor 1 in from the front. Figure 7. Fasten the front of the FastStor 1 to the rack. 6 FastStor 1 Quick Installation Guide Use one M5x8 screw on both left and right sides (M5-thread) to fasten the FastStor 1 to the rails' backside. Figure 8. Fasten the rear of the FastStor 1 to the rails. Step 3. Connecting Power Cable Before connecting the FastStor 1 to your host computer system, you should run the unit's self-diagnostic test. (This preparation requires power to the FastStor 1. ) Follow these steps to perform this test: 1. Use the power cables from the accessories included in the shipment. Make sure you select the power cord suited for your location's power system. Plug the power cable into the rear of the FastStor 1 (see Figure 9). Plug the other end of the cable into a properly grounded electrical outlet. Note: Reliable grounding depends on grounding in the AC electrical outlet in which the FastStor 1's power cable is connected. Adding the FastStor 1 to an existing rack installation can cause a leaking current fault condition because of the summation of the leaking currents. For security, a 250V 2A (H) fuse is located near the power switch. 3. [. . . ] Restarting Your System ADIC recommends that all external SCSI devices, including the FastStor 1, are powered on before you restart the computer system. After restarting your system, including the FastStor 1, the FastStor 1 runs a power-on selftest (as in Step 5 above). When the display reports that the FastStor 1 is in the "Idle" state and the green LED is on, the FastStor 1 is ready for further configuration and operation. Note: The tape drive needs up to 40 seconds from power on until it's active on the SCSI bus. [. . . ]