Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual QUANTUM FIRMWARE UPDATE. We hope that this QUANTUM FIRMWARE UPDATE user guide will be useful to you.
Lastmanuals help download the user guide QUANTUM FIRMWARE UPDATE.
Manual abstract: user guide QUANTUM FIRMWARE UPDATE
Detailed instructions for use are in the User's Guide.
[. . . ] Appendix C UPDATING THE FIRMWARE
This chapter explains how to update the tape drive's PCBA-resident firmware.
C. 1
OVERVIEW
Using the tape drive's front panel and a tape with the updated firmware image, you can update the tape drive's PCBA-resident firmware.
CAUTION If a powerfail occurs during the firmware update process (when the new image is actually being programmed into the FLASH EEPROMs), the tape drive's PCBA will be rendered unusable. When performing a firmware update, take all possible precautions to prevent power failure to the tape drive.
C. 2
CREATING A FIRMWARE UPDATE TAPE
To update the tape drive's PCBA firmware, you need a tape cartridge with a copy of the new firmware image. The firmware image must be byte-written without compression onto the tape using the appropriate block size as defined in Table C1. [. . . ] When performing a firmware update, take all possible precautions to prevent power failure to the tape drive. Make sure you have a DLTtape that bears the firmware image of the required revision level copied to it. Put the tape drive into the firmware update mode. To do this: a) Remove any cartridge in the target tape drive and close the handle (down position). b) Press the UNLOAD button on the drive front panel and hold the button until the WRITE PROTECT indicator begins blinking (approximately six seconds). This indicates that the tape drive has recognized your request for firmware update mode and is waiting for the sequence to complete.
C-2
Quantum DLT 7000 Tape System
Appendix C: Updating the Firmware
NOTE If the WRITE PROTECT indicator does not blink, check that: 1. The drive handle is in its down position. c) Release the UNLOAD button, then press the UNLOAD button again within four (4) seconds. The second press should take less than one (1) second. d) The TAPE IN USE and the WRITE PROTECT indicators will blink. This indicates that the tape drive recognizes that the firmware update mode has been selected. If you are unsuccessful in selecting the firmware update mode (if, for example, pressing the UNLOAD button the second time requires longer than one [1] second), the WRITE PROTECT indicator will stop blinking within several seconds. If the drive and controller PCBA are not communicating properly, you cannot select the firmware update function. Once the firmware update mode has been successfully selected, insert the cartridge with updated firmware image into the drive. The drive then:
· · ·
Automatically reads the cartridge. The tape will move for a few minutes performing calibration and directory processing before any data is read. [. . . ] The firmware update cartridge is NOT unloaded. The tape drive subsystem may still be usable. Failure may be a result of:
· · ·
·
Power failure Bad firmware image on the tape Non-functioning FLASH EEPROMS.
Table C-2 provides troubleshooting information.
C-4
Quantum DLT 7000 Tape System [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE QUANTUM FIRMWARE UPDATE
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual QUANTUM FIRMWARE UPDATE will begin.