User manual QUANTUM FREEXWIRE FW11

[. . . ] . Wireless QTTL® control for Digital Cameras . . Wireless TTL control for Film Cameras (non pre-flash) . . Wireless Auto mode for any Qflash without TTL Adapter . . Sync-in connections- camera to Transmitter FW9T . [. . . ] When mounting the FW12 or FW11 to a Dead Shoe (model 512) it will be necessary to connect a sync-in cable for FW9T units, or sync-out cable for FW8R units. See Appendices A and B. 9 5. 3: Direct Hot Shoe Mounting with FW12 or FW11 Connect the Hot Shoe Adapter FW12 or (Uni-Mod FW11) to a Transmitter FW9T and slip it into a camera hot shoe. The purpose of the Hot Shoe Adapter is only to provide hot shoe mounting and sync from a camera to a Transmitter FW9T. FW11 or FW12 will not provide TTL control -- see Appendix D for selection of QTTL and other TTL adapters. A Receiver FW8R mounted to FW11 or FW12 on a camera shoe will have no connection to the shutter release. If you desire wireless shutter release, connect a separate Shutter Release Cord (see appendix C) between the FW8R MD socket and the shutter release connection on the camera. 5. 4 Mounting FW7Q Turn off Qflash power before mounting the FW7Q. FW7Q plugs into the lower Accessory socket of Qflash, as shown in the diagram. For added stability a hook-and- loop pad is mounted on the back of Receiver FW7Q. One part of this pad will be attached to the Qflash housing as follows: Note where the hook and loop pad will come into contact with the Qflash housing when FW7Q is plugged into the lower Accessory socket. Remove the adhesive liner from the pad (without touching the MOUNTING FW7Q adhesive), and align and mount FW7Q. 8. 1 Transmitter FW9T set-up: Select the correct type of Qflash TTL Adapter for your camera, from the list in Appendix D or our website. FW series of TTL adapters attach to Transmitter FW9T and to the camera hot shoe without cables. QF series TTL Adapters connect to Transmitter FW9T accessory socket and require an FW11 Uni-Module. D or Dw series QTTL adapters connect to Transmitter FW9T and DO NOT require other accessories. Mount FW9T on a bracket or other location, or use an FW series Adapter which mounts directly to the camera hot shoe. 8. 2 Receiver FW8R or FW7Q: Mount and connect one or more of these receivers as in Section 7. 2 8. 3 Optional: connect a local Qflash to the Transmitter FW9T: A local Qflash connected to FW9T will sync with the remote flash and will also power the FW9T. Set the power switch of the FW9T to EXT. Set Qflash to TTL mode. FW9T FW31 FW9T QF, D or Dw SERIES ADAPTER FW9T 9. 0 Wireless Auto Mode ­ for any Qflash ­ without 4. 0 TTL Adapters FW SERIES TTL ADAPTERS SHOE MOUNT With today's complicated camera systems, it is sometimes easier, more reliable and straightforward to shoot in auto mode rather than TTL. Auto also gives the photographer the ability to tailor her/his exposures to personal taste or experience. This mode will give any model of Qflash wireless Auto mode control of remote Qflashes. This set up does not require a camera with TTL capability nor a TTL Adapter, only local and remote Qflashes. 9. 1 Transmitter FW9T set-up: Connect an FW31 cable from Transmitter FW9T to Qflash. [. . . ] (51g) 2x AAA cell alkaline, nicad, nickel-metal hydride, or lithium FW8R: receiving four synchronizations per minute: 24000 shots, 100 hours; FW9T: sending synchronizations shots per minute: 36000 shots, 150 hours Remaining battery life- after low battery signal (triple blink every 2 seconds): approx. 1-3 hours Weight (w/ batteries): FW52 FW53N Batteries: Battery life:(alkaline): FW57 FW59 FW60 FW64 FW65 D19w D25w * FW series TTL Adapters connect directly to the FREEXWIRE TX FW7Q requires no batteries. Any FREEXWIRE connected to Qflash with FW31 cable requires no batteries. Maximum Range: Maximum flash rate: Maximum sync delay from camera trigger to remote flash: Minimum camera shutter speeds: See Section 11. [. . . ]