User manual QUANTUM GOVAULT FOR WINDOWS 06-2007

[. . . ] GoVaultTM for Windows User's Guide, P/N 20013264-001, June 2007 Product of USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. COPYRIGHT STATEMENT Copyright 2007 by Quantum Corporation. [. . . ] 3 On the General tab, under the System heading, look for the words x64 Edition. IF . you see x64 Edition, you do not see x64 Edition, the system is a 64-bit Itanium, THEN use the . system application applet x64 x86 IA64 Installing the GoVault System Application Software 2 After determining which system application applet you need to use, install the GoVault system application software on your workstation or server system as follows: 1 Insert the GoVault Resource CD into the CD-ROM drive. 2 Browse the CD contents to find the SetupGoVault. msi file for the appropriate system application applet. 3 Double-click the SetupGoVault. msi file to launch the GoVault Setup Wizard (see figure 11). 4 Click Next to continue and display the License Agreement dialog (see figure 12). GoVaultTM for Windows User's Guide 17 Chapter 2 Installation Procedures Installing the GoVault System Application Software Figure 11 GoVault Setup Wizard GoVaultTM for Windows User's Guide 18 Chapter 2 Installation Procedures Installing the GoVault System Application Software Figure 12 License Agreement Dialog 5 Read the License Agreement, select I Agree, and click Next to continue and display the Select Installation Folder dialog (see figure 13). GoVaultTM for Windows User's Guide 19 Chapter 2 Installation Procedures Installing the GoVault System Application Software Figure 13 Select Installation Folder Dialog 6 Use the Select Installation Folder dialog to specify the location where you want to install the GoVault system application software. 7 The default location is shown in figure 13. If you want to specify a different location, click Browse and navigate to the file location that you want. 8 Click Next to continue and display the Confirm Installation dialog (see figure 14). GoVaultTM for Windows User's Guide 20 Chapter 2 Installation Procedures Installing the GoVault System Application Software Figure 14 Confirm Installation Dialog 9 Click Next to start the installation. 10 Appearance of the Installation Complete display signifies a successful installation of the GoVault system application software (see figure 15). 11 As prompted, click Close to exit the GoVault Setup Wizard. GoVaultTM for Windows User's Guide 21 Chapter 2 Installation Procedures Installing the GoVault System Application Software Figure 15 Installation Complete Display 12 Remove the GoVault Resource CD from the CD-ROM drive. 13 Verify successful installation of the GoVault system application software by right-clicking the GoVault drive letter and seeing the Set Password and GoVault Help options on the menu display 14 If you are going to install the included backup application, or another backup application, proceed to Installing the Backup Application Software in the following subsection. If you are not going to install a backup application, skip to Registering GoVault. GoVaultTM for Windows User's Guide 22 Chapter 2 Installation Procedures Installing the Backup Application Software Installing the Backup Application Software GoVault for Windows includes a robust backup application. After you have installed the GoVault dock and cartridge hardware and the GoVault system application software: IF you want to install . the included backup application software, some other backup application software, THEN refer to the installation instructions provided . by the other backup application software supplier. Before installing any other backup application software, check the Compatibility Guide on the Quantum website to verify that it is compatible with GoVault: www. quantum. com/ServiceandSupport/CompatibilityGuides/Index. aspx After installing the backup application software, proceed to Registering GoVault in the following subsection. Registering GoVault After installing GoVault for Windows, register it via the Quantum website at: www. quantum. com/registration Registering GoVault for Windows ensures that you will receive the latest technical information about the drive, as well as other product, service, and support information. GoVaultTM for Windows User's Guide 23 Chapter 3 3Operation This chapter describes how to use the GoVaultTM for Windows dock and cartridge disk drive, including: This chapter describes how to use GoVaultTM Tabletop. Topics include: · Understanding the Activity LED Indicator Display on page 25 · Inserting and Ejecting Cartridges on page 26 · Attaching Labels to Cartridges on page 31 · Changing the Volume Label of Cartridges on page 33 · Reformatting Cartridges on page 33 · Accessing GoVault System Application Software Features, which are: · · · Using Cartridge Password Protection on page 37 Checking the GoVault Dock and Cartridge Status on page 44 Updating the GoVault Firmware on page 47 · Handling Operational Fault Conditions on page 49 GoVaultTM for Windows User's Guide 24 Chapter 3 Operation Understanding the Activity LED Indicator Display Understanding the Activity LED Indicator Display The on/off or flashing condition of the green activity LED indicator on the front panel of the GoVault dock displays the various status conditions, as shown in table 1. Table 1 Activity LED Indicator Display Definitions When the LED . is off, is on continuously, and not flashing, It means that the GoVault dock . is not functioning properly, or there is no power to the dock. is functioning correctly and either: · There is no cartridge in the dock. · A cartridge load operation has completed and there is a cartridge in the dock. is flashing on slowly, approximately once per second, is performing one of the following operations: · Data transfer · Cartridge security erase or encountered a cartridge medium error condition, such as an incompatible file format, device communication problem, and so on. is flashing on quickly, approximately once per second, is flashing on quickly, approximately two times per second, is flashing on quickly, approximately four times per second, firmware update is in progress. is unloading a cartridge. temperature or voltage is out of range (internal dock only). GoVaultTM for Windows User's Guide 25 Chapter 3 Operation Inserting and Ejecting Cartridges When the LED . is flashing on very quickly, approximately eight times per second, It means that the GoVault dock . [. . . ] Close the Device Manager window and enjoy your GoVault installation. If you do see QUANTUM GoVault listed as either an Intel(R) XXXXX Serial ATA Storage Controller or an Intel(R) XXXXX Ultra ATA Storage Controller, then it is true that the GoVault device server is connected GoVaultTM for Windows User's Guide 68 Appendix B Configuring Windows for DMA Data Transfer Mode Changing the Transfer Mode to the system by an Intel or an Intel-compliant motherboard with either an Intel or an Intel-compliant ICH5, ICH6, or ICH7 I/O Controller Hub. In this case, PIO is configured as the data transfer mode, and you should use the procedure in Changing the Transfer Mode to configure high-speed DMA mode for your GoVault data transfer operations. Do not close the Device Manager window. Changing the Transfer Mode If the procedure in Determining Your Motherboard Configuration indicated that PIO is the GoVault data transfer mode, change it to DMA mode as follows: 1 Right-click QUANTUM GoVault in the Device Manager window and select Properties to display the QUANTUM GoVault Properties dialog (see figure 41). Figure 41 GoVault Properties Dialog GoVaultTM for Windows User's Guide 69 Appendix B Configuring Windows for DMA Data Transfer Mode Changing the Transfer Mode 2 Note the indicated Location: value, which might show Location 1 (1) or Location 0 (0) on your workstation or server system. [. . . ]