Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual QUANTUM HP900 S700 CONFIG. We hope that this QUANTUM HP900 S700 CONFIG user guide will be useful to you.
Lastmanuals help download the user guide QUANTUM HP900 S700 CONFIG.
Manual abstract: user guide QUANTUM HP900 S700 CONFIG
Detailed instructions for use are in the User's Guide.
[. . . ] Quantum Corporation
DLTtapeTM Application Note
_____________________________________________________________________________________________
DLTtapeTM Installation on HP® 9000 Series 700 System
HP-UX® 9. X This application note is to be used only as a guideline for the titled subject. The user assumes all responsibility for understanding the interrelationships of this information with other affected software or system products. [. . . ] The DLT controller firmware must have OEM-1 controller firmware installed. Installation The system must have the appropriate SCSI interface for DLT drive to attach to, i. e. , a SCSI single-ended DLT drive can be attached only to a SCSI single-ended interface. The same is true for SCSI differential attachment. The hardware attachment simply requires the DLT tape peripheral to be attached to the interface while the system is powered down. After the DLT tape peripheral has been attached, you will need to perform certain system operations that will allow DLT device system recognition. Perform the installation as follows: Shutdown the system and remove AC power from the system. Install the DLTtape peripheral and connect it to the SCSI controller. Depending on the DLT tape peripheral you are installing, refer to one of the following manuals for switch and jumper settings and SCSI bus termination: · · · · · · DLT2000/DLT2700 product manual (order number 81-109132) DLT2500 owner's manual (order number 81-109374) DLT2000XT/DLT2500XT/DLT2700XT product manual (order number 81-109253) DLT4000/DLT4500/DLT4700 product manual (order number 81-106336) DLT7000 Tape Drive product manual (order number 81-60000) DLT8000 Tape Drive product manual (order number 81-60118)
Set the DLT SCSI device address to an unassigned SCSI ID. During the powerup, the process allows you to stop the sequence by pressing the ESC key. By doing so, you can verify drive attachment by issuing a search for boot device selection. [. . . ] These device files allow certain DLT device modes of operation. Enter the following commands: mknod 1m c 54 0x201402 mknod 1mn c 54 0x201403 mknod 1c c 54 0x2014c2 mknod 1cn c 54 0x2014c3 The device files created are for an installed DLT device with a SCSI ID of 4 and are shown below along with their corresponding operating characteristics: 1m - drive 1, rewind on close 1mn - drive 1, no rewind on close 1c - drive 1, compressed, rewind on close 1cn - drive 1, compressed, no rewind on close Associating the device files to a DLT device with a SCSI ID other than 4 requires that the number "4" in the minor number of the mknod command be changed to the new ID.
Copyright 1999-2001 Quantum Corporation or its subsidiaries or affiliates. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE QUANTUM HP900 S700 CONFIG
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual QUANTUM HP900 S700 CONFIG will begin.
