User manual QUANTUM INST GUIDE CD72LW1U UPGRADE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual QUANTUM INST GUIDE CD72LW1U UPGRADE. We hope that this QUANTUM INST GUIDE CD72LW1U UPGRADE user guide will be useful to you.

Lastmanuals help download the user guide QUANTUM INST GUIDE CD72LW1U UPGRADE.


Mode d'emploi QUANTUM INST GUIDE CD72LW1U UPGRADE
Download
Manual abstract: user guide QUANTUM INST GUIDE CD72LW1U UPGRADE

Detailed instructions for use are in the User's Guide.

[. . . ] Installing a Second Drive in the 1U System Required tools: #1 and #2 Phillips Head screwdrivers Inventory of Components: (1) DAT 72 Tape Drive (1) IO adapter bracket, with an internal SCSI cable, SCSI ID switch, and a SCSI ID cable attached (2) Drive tab mount brackets (2) M3 x 0. 5 flathead Phillips screws for drive tab mounts (6) Wire ties to secure the cables to the 1U chassis 1. Remove all power from the system and remove the power cord from the receptacle. Filler Panel Blank I/O Panel Standard screw Figure 1 Figure 2 2. [. . . ] Once the holes on the drive bay are lined up with the holes on the drive tab mounts, the front of the drive should be flush with the front panel of the system. Secure the drive tab mounts to the system with a #1 Phillips Head screwdriver and the two screws provided (Figure 3D). Purple Wire I/O Bracket Figure 4B Bulkhead Opening 6. Install the IO bracket with the attached cables. Insert the tab on the IO bracket into the rear panel of the system. Tighten the standard screw to secure the bracket to the system. Route the SCSI and SCSI ID cables through the opening in the bulkhead to the back of the second drive. Carefully connect the SCSI cable to the back of the second drive. Connect the SCSI ID cable into the second drive's SCSI ID connector (Figure 4A). Orient the SCSI selector cable so its purple wire is visible and against the power connector. Insert the power connector from the power source into the power input of the second drive (Figure 4B). Secure the cables to the system chassis by threading a wire tie through the wire tab on the chassis floor and securing the tie over the SCSI cable (Figure 4C). Replace the top cover and reinstall the system into the rack. [. . . ] To change the SCSI ID, press the buttons above or below the SCSI Indicator on the back of the system (Figure 5). Figure 4A Figure 4C SCSI ID Switches Power Cable Note: If the default SCSI ID is changed, turn the drive power off and back on. SCSI Cables Figure 5 10. Connect the power cord to the power receptacle on the back left side of the system (Figure 5). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE QUANTUM INST GUIDE CD72LW1U UPGRADE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual QUANTUM INST GUIDE CD72LW1U UPGRADE will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag