User manual QUANTUM L200PAK

[. . . ] 0 February 1999 ATL PowerStor L200 Series Library Unpacking Instructions Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Library Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Selecting an Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Floor Space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Overhead Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Surface Strength and Inclination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power and Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Unpacking the Library. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Uncrating the Rack-Mount Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing the Rack-Mount Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Uncrating the Library. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1 ATL PowerStor L200 Series Library Unpacking Instructions Document 6322502-01, Ver. 0 February 1999 2 ATL PowerStor L200 Series Library Unpacking Instructions Document 6322502-01, Ver. 0 February 1999 0 0 Introduction Purpose 0 0 The ATL PowerStor L200 Series is an automated storage and retrieval library system consisting of one DLTTM tape drive and eight DLTtape cartridges (see figure 1). [. . . ] If the library will be placed on a desk or table, make sure it is sturdy enough to support the library's weight (37 lbs/16. 8 kg). Power and Grounding 2 The electrical ratings for the library are 100 to 120/200 to 240 VAC, 50/ 60 Hertz. Environmental Specifications 2 The installation location should meet the following environmental specifications. · · · · · · · · Temperature: 50°F to 104°F (10°C to 40°C) Relative humidity: 20% to 80% noncondensing Humidity gradient: 10% per hour Dry bulb temperature: 50°F to 104°F (10°C to 40°C) Wet bulb temperature: 77°F (25°C) Temperature gradient: 19. 8°F per hour (11°C per hour) across the range Temperature shock: 18°F (10°C) over two minutes Altitude: -500 feet to 30, 000 feet (-152. 4 meters to 9144 meters) Selecting an Installation Location 5 ATL PowerStor L200 Series Library Unpacking Instructions Document 6322502-01, Ver. 0 February 1999 Unpacking the Library Unpack the library as close to the installation location as possible. The unpacking instructions vary depending upon whether you received a desktop or rack-mount library. If you received a desktop library, you should have only one shipping carton. Follow the instructions in "Uncrating the Library" on page 7 to unpack the library. If you received the rack-mount library, you will have two shipping cartons. The large carton contains the library, and the smaller carton contains the rack-mount kit. To unpack and install the rack-mount library, you must: · · · Uncrate the rack-mount kit and verify its contents (see "Uncrating the Rack-Mount Kit"). Install the rack-mount kit in the rack (see "Installing the Rack-Mount Kit"). Uncrate the library and place it in the rack (see "Uncrating the Library"). 2 Before You Begin 2 Inspect the shipping pallet and carton for damage that may have occurred during shipment. Report any damage to the shipper immediately. Uncrating the Rack-Mount Kit 2 Cut the packing tape at the top of the shipping carton and unpack the rack-mount kit. Before installing the rack-mount kit in the rack, compare the contents of the carton with the packing list inside the shipping carton. Installing the Rack-Mount Kit 2 Install the rack-mount kit in the rack, referring to the drawing provided in the shipping carton. 6 Unpacking the Library ATL PowerStor L200 Series Library Unpacking Instructions Document 6322502-01, Ver. 0 February 1999 0 0 Uncrating the Library 2 To uncrate an ATL PowerStor L200 Series library: Procedure 1 Cut the straps that secure the shipping carton to the pallet (see figure 3). [. . . ] If it is a rack-mount library, place it in the rack. 7 8 8 Unpacking the Library ATL PowerStor L200 Series Library Unpacking Instructions Document 6322502-01, Ver. 0 February 1999 0 0 Figure 5 Removing the Library from the Shipping Carton Packing foam Library Shipping bag The library is now unpacked. Refer to the ATL PowerStor L200 Series Library User's Guide for information about connecting the library cables and operating the library. Unpacking the Library 9 [. . . ]