User manual QUANTUM P1000GUID

[. . . ] ATL P1000 Series Tape Library User's Guide 6221101-03 Ver. 0 ATL P1000 Series User's Guide, 6221101-03, Ver. provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. may revise this publication from time to time without notice. [. . . ] Pressing this button moves you forward screen-by-screen through previously selected screens. Pressing this button returns you to the initial GUI screen (see figure 29 on page 42). Pressing these buttons adjusts the contrast of the GUI. Forward button Home button Contrast buttons ( and ) Main Display Area 3 The main display area provides access to five tabbed screens through which you can issue commands to the library. To view a screen, press its corresponding tab. Since the GUI is not large enough to display all five tabbed screens at once, the initial GUI screen displays only the first three screens (Overview, Tapes, and Operator). To scroll forward to the remaining screens (Service and Prism Router), press the right arrow button. To scroll backward through the screens, press the left arrow button. Press this button Press this button to scroll to the to scroll to next tabs. previous tabs. Back PRODUCTS Figure 30 Navigating through the GUI Screens Forward Tapes Home Operator PRODUCTS Back Forward Tapes Test Home Service Misc. ATL System Off-line ATL System Off-line Overview Operator Report Drives D00 ANF 120 Ready D02 empty Ready Activity Load Pack P00 ANF146 P01 ANF147 Standby Load Port Load Pack Standby Statistics Load Port Load Pack Actuator SysTest Library Results SysTest Library Initialize Nonvol Statistics D01 ???Ready D03 ANF 123 Ready GRP empty P02 ANF148 P03 ANF149 Auto Clean Operate Axes U Stop S Stop Service Calibrate Initialize Nonvol Config Change Password 44 ATL P1000 Series User's Guide Chapter 3 Basic Operations Using the GUI Table 6 describes each of the GUI screens. Table 6 GUI Screens Screen Overview Tapes Description This screen provides an overview of the tape drives, robot activity, and load pack inventory. This screen displays the contents of the tape drives, storage bins, load packs, the gripper, and the load port. This screen contains the library configuration and control functions. To use this screen, you must have Operator or Service access privileges. This screen contains reporting functions, system tests, and miscellaneous commands. To use this screen, you must have Service access privileges. This screen contains options related to the optional Prism FC210 Router. For information about these options, see the ATL Prism FC210 Router Addendum (PN 6331101). Operator Service Prism Router GUI Screens 3 Figure 31 shows the commands that are available on the Overview, Tapes, Operator, and Service screens. Figure 31 GUI Screens Overview Tapes Operator Service Tape Drive Status Activity Load Pack Drives Storage Load Pack Transport Load Port Configure Library Configure Options Move Cartridges Inventory Tapes Calibrate Library Exercise Library Unload Drive Unload Imp/Exp Statistics Actuator Sys Test Library Results Auto Clean Sys Test Library Operate Axes Service Calibrate Initialize Nonvol Statistics Initialize Nonvol Config. Change Password ATL P1000 Series User's Guide 45 Chapter 3 Basic Operations Obtaining Library Status Obtaining Library Status You can obtain library status from the Overview and Tapes screens. 3 Overview Screen 3 To open the Overview screen, press the Overview tab on the GUI. The Overview screen is divided into three sections (see figure 32): · · · Drives Activity Load Pack Figure 32 Overview Screen Back PRODUCTS Forward Tapes Home Operator Drive Cartridge number present ATL System Off-line Overview Drives D00 ANF 120 Ready D02 empty Ready Activity Load Pack P00 ANF146 Drive status Standby Load Port Load Pack D03 ANF 123 Ready Bar code Writeenabled P01 ANF147 D01 ???Ready D03 ANF 123 Ready P03 ANF149 GRP empty P02 ANF148 Compression enabled U Stop 46 ATL P1000 Series User's Guide Chapter 3 Basic Operations Obtaining Library Status Drives 3 The Drives section of the Overview screen displays the following information: · · · · whether a tape drive has a cartridge the bar code number of the cartridge (if a cartridge is present and the label is readable) whether the cartridge is write-enabled or write-protected whether compression is enabled To view more detailed information about drive status, press the Overview screen anywhere in the Drives section. This opens a Tape Drive Status box (see figure 33). Use the arrow buttons to scroll through the list of drives. To return to the Overview screen, press the Tape Drive Status box. Figure 33 Overview Screen with Expanded Tape Drive Status Back PRODUCTS Forward Tapes Home Operator Load Pack P00 ANF146 P01 ANF147 GRP empty P02 ANF148 P03 ANF149 ATL System Off-line Overview Tape Drive Status Activity Standby Load Port Load Pack D03 ANF 123 Ready Compression ON Write Protect OFF DLT7000 CompacTape IV SCSI ID: 05 U Stop Activity 3 The Activity section of the Overview screen displays the source element, transport medium, and destination element involved in any current move activity. ATL P1000 Series User's Guide 47 Chapter 3 Basic Operations Obtaining Library Status Load Pack 3 The Load Pack section of the Overview screen identifies the cartridges currently stored in the load pack. [. . . ] bar code scanner A device mounted on the extension axis that reads the cartridge bar code labels. bulk pack An 8-bin removable storage magazine for cartridges. The bulk pack fits inside the right front door of the P1000 library. C calibration The software measurements and configuration required for successful library operation. extension axis assembly Mounted on the vertical axis, the extension axis assembly consists of the gripper assembly and the horizontal axis on which the gripper assembly is mounted. [. . . ]