User manual QUANTUM PX500 TAPE DRIVE INSTALLATION INSTRUCTIONS 81-81301-04 A01

[. . . ] 22 Fibre Channel Connectivity Troubleshooting 24 Fibre Channel Connectivity Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 SCSI ID Assignment with Native Fibre Channel Tape Drives. . . . . . . . . . . . . 25 81-81301-04 A01, August 2006 1 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-04 A01 August 2006 Made in the USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. [. . . ] The OCP displays the Setup screen (see figure 12): Figure 12 Setup Screen Enter 2 Use the up and down arrows to highlight Cabinet and press Enter. The Cabinet screen displays (see figure 13): Figure 13 Library Options Screen 3 Use the up and down arrows to highlight Host bus and press Enter. The Host bus screen displays (see figure 14): Setting the Tape Drive SCSI ID 15 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-04 A01 August 2006 Figure 14 Host Bus Options Screen 4 Use the up and down arrows to highlight the tape drive receiving the new SCSI ID and press Enter. 5 Use the up and down arrows to select a SCSI ID and press Enter to set the ID. 6 When you have completed setting the SCSI IDs, press Exit to return to the Cabinet screen. 7 From the Ops screen, use the up and down arrows to highlight Drive Operations and press Enter. The Drive Operations screen displays (see figure 15): Figure 15 Drive Operations Screen 8 Use the up and down arrows to select a tape drive and press Enter. 9 Use the up and down arrows to select Off and press Enter. The tape drive powers down and returns to the Drive Operations screen. 10 Use the up and down arrows to select On and press Enter. The tape drive powers on and is ready for use. The WWNs must be determined and recorded both for the customer and for 18 Completing the Native Fibre Channel Installation Quantum PX500 Series Tape Drive Installation Instructions 81-81301-04 A01 August 2006 Quantum customer support. This information is important when replacing the Fibre Channel SCB and tape drives. Using the following procedures, complete table 2 and retain a copy of the table for your records. Have this table available when contacting Quantum Customer Support for any library or tape drive connectivity issues. Table 2 Library World Wide Names Library/Tape Drive Media Changer (robot) Tape drive 1 Tape drive 2 Tape drive 3 Tape drive 4 Tape drive 5 Tape drive 6 Tape drive 7 Tape drive 8 Tape drive 9 Tape drive 10 World Wide Name (e. g. 50:05:08:40:00:16:47:00) Using the Remote Management to Determine the WWNs To determine the WWNs from the library remote management pages: 1 On the host computer, open the internet browser software. 2 In the Address field, type http://IPaddress/ where IP address is the IP address for the Quantum PX500 series library. 3 Enter the username and password and click OK. Note: The default username and password is admin. 0 The Overview page displays (see figure 19): Completing the Native Fibre Channel Installation 19 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-04 A01 August 2006 Figure 19 Overview Page 4 Click Setup from the contents frame. The management frame displays the Setup page (see figure 20). Figure 20 Setup Page 5 Click on the SCSI/Fibre tab. The SCSI/Fibre page displays (see figure 21). 20 Completing the Native Fibre Channel Installation Quantum PX500 Series Tape Drive Installation Instructions 81-81301-04 A01 August 2006 Figure 21 SCSI/Fibre Page Media changer Tape drives Connectivity type 6 For the Media Changer and Tape Drives, click Fibre under the Connectivity type. The Media Changer (see figure 22) and Tape Drive Configuration (see figure 23) screen displays. Figure 22 Media Changer Configuration Screen World wide name Completing the Native Fibre Channel Installation 21 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-04 A01 August 2006 Figure 23 Tape Drive Configuration Screen World wide names (port 0 and port 1) 7 Record the WWNs for the media changer and tape drives in table 2. Note: These numbers are the world wide NODE names for the library and tape drives. [. . . ] The host (including the laptop using MAGMA box) will pick up the devices and assign local SCSI IDs in the order that the SAN devices are discovered. This will in almost every case NOT match the order of the devices as they are installed in the library. This is not a problem from the customer point of view, as long as drive serialization is enabled on the library and serialization is supported by the customers ISV application. This will allow the ISV application to put the drives in the correct order within the application. [. . . ]