User manual QUANTUM PX500 USERS GUIDE 81-81290-04 A01

[. . . ] Quantum PX500 Series User's Guide, 81-81290-04 A01, August 2006, Made in USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. COPYRIGHT STATEMENT Copyright 2006 by Quantum Corporation. [. . . ] In all modes, the secure key is used to read data from cartridges that have a pre-existing secure key. If the secure key on the cartridge does not match the current secure key on the library, the data on the cartridge can not be read. Three write protection modes are available: Quantum PX500 Series User's Guide 128 Chapter 3 Quantum PX500 Series Remote Management Setup · · · Never Write Secure Key to a Cartridge - The secure key will never be written to a cartridge placed in a secured tape drive. Only Write Secure Key to Blank Cartridges - The secure key will only be written to blank, unformatted cartridges. Write Secure Key to All Cartridges - The secure key will be written to all cartridges, including blank and formatted cartridges containing data. This mode may be used to apply a secure key to cartridges with pre-existing data. Enable/Disable Secure Key for Drives 3 Refer to figure 83 for information on Enable/Disable Secure Key for Drives. Figure 83 Enable/ Disable Secure Key for Drives The secure key can only be used with tape drives that are secure key capable. This section lists the tape drives in the library that are secure key capable. A checkmark in the Secure Key column indicates a secure key is enabled for the tape drive. 1 The secure key can be enabled or disabled for all tape drives by clicking the corresponding radio button. 2 Click the Secure Key check box for individual tape drives to enable/ disable secure key for a tape drive. Note: The system must be offline to Enable/Disable Secure Key setting for drives. Quantum PX500 Series User's Guide 129 Chapter 3 Quantum PX500 Series Remote Management Setup Modify Secure Key for Library Refer to figure 84 for information on Modify Secure Key for Library. 3 Figure 84 Modify Secure Key for Library To modify the secure key used by the library: 1 Select the secure key name from the list of available names. Note: Selecting None to will cause the library to NOT use a secure key. 2 Click Update. Note: The system must be offline to modify a secure key. Assign Secure Key to Cartridge Refer to figure 85 for information on Assign Secure Key to Cartridge. 3 Quantum PX500 Series User's Guide 130 Chapter 3 Quantum PX500 Series Remote Management Setup Figure 85 Assign Secure Key to Cartridge Click Find to list all secured cartridges and their assigned secure key names. To assign a secure key to a cartridge: 1 Enter the barcode of the cartridge. Separate multiple barcodes with either spaces or commas. 2 Select a secure key name from the list of available names. 3 Selecting Remove will remove the association between the cartridge and a secure key name in the cartridge database. 4 Click Update to accept the changes. Create Secure Key Name/Secure Key Pair 3 Refer to figure 86 for information on Create Secure Key Name/Secure Key Pair. Quantum PX500 Series User's Guide 131 Chapter 3 Quantum PX500 Series Remote Management Setup Figure 86 Create Secure Key Name/ Secure Key Pair To create a secure key name/secure key pair: 1 Enter the Secure Key Name. Note: The secure key name must be less than 12 characters, may include spaces, but cannot contain the following characters: ( ) = ; 2 Enter a securekey in the protected Secure Key field. 3 Enter the same secure key in the Verify Secure Key field. Note: The Secure Key must be at least 8 characters and no more than 32 characters. The Secure Key must also contain at least one non-alphanumeric character and cannot include spaces or double quotes (""). 4 Click New to create the secure key name/key pair. Delete Secure Key Name Refer to figure 87 for information on Delete Secure Key Name. 3 Quantum PX500 Series User's Guide 132 Chapter 3 Quantum PX500 Series Remote Management Setup Figure 87 Delete Secure Key Name The Secure Key Names maintained on the library are displayed in one of three lists: · · Unused Secure Keys - keys not associated with any cartridges or tape drives currently in the system. Inactive Secure Keys - keys associated with cartridges in the library, or currently assigned to the library, but not assigned to any tape drives. [. . . ] Om utrustningen levereras i Kanada, använd den CSA-certifierade nätsladden som specificeras nedan för användning med 100-120 V. 244 Quantum PX500 Series User's Guide Appendix E Regulatory Statements Notice for USA and CANADA Only Kontaktkåpa Sladd Längd Märkvärde Parallellt blad med jordstift (NEMA 5-15P-konfiguration) Typ: SJT, tre 1, 5 mm2 (16 AWG) eller 1, 0 mm2 (18 AWG) ledare Maximalt 15 fot (4, 5 m) Minimalt 10 A, 125 V Lasermeddelande FÖRSIKTIGHET: Med alla paneler och luckor på plats klassificeras denna produkt som en laserprodukt klass 1. Streckkodsläsaren inuti produkten är klassificerad som en laserprodukt klass II. Undvik kontakt med streckkodsläsarens laserstråle. FÖRSIKTIGHET: Användning av kontroller, justeringar eller utförande av rutiner andra än de som anges i detta dokument kan leda till farlig exponering för strålning. Meddelande om biblioteksbatteri FÖRSIKTIGHET: Produkten innehåller ett litiumbatteri. [. . . ]