User manual QUANTUM SNC 5100 FOR THE SCALAR 1000 AND 10K

[. . . ] SNCTM 5100 for the Scalar ® 1000 and 10K User Guide Copyright Notice © Copyright ADIC 2002 The information contained in this document is subject to change without notice. This document contains proprietary information which is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without prior written consent of ADIC. ADIC shall not be liable for errors contained herein or for incidental or consequential damages (including lost profits) in connection with the furnishing, performance or use of this material whether based on warranty, contract, or other legal theory. [. . . ] Low humidity and heating increase static electricity. 6-00020-02 Handling Electrostatic Discharge-Sensitive Parts 81 SNC 5100 Removing and Replacing the GBIC Caution Shut down the host systems to ensure that all I/O through the SNC 5100 has stopped. Removing the GBIC Caution You must stop I/O at the Fibre Channel host. Review "Handling Electrostatic Discharge-Sensitive Parts" on page 81. Place the GBIC in a static-protective bag. Replacing the GBIC Caution You must stop I/O at the Fibre Channel host. Review "Handling Electrostatic Discharge-Sensitive Parts" on page 81. Insert the known good GBIC into the slot. Remove the dust caps from a known good GBIC. Plug the Fibre Channel cables back in, being sure to use the correct polarity. If you were sent here by another MAP, return to it. Before Removing or Replacing the Unit These steps are performed if a repair action is required for any component of the SNC 5100, except for a GBIC. 82 Removing and Replacing the GBIC 6-00020-02 SNC 5100 Caution Shut down the host systems to ensure that all I/O through the SNC 5100 has stopped. Verify that the latest configuration has been saved. For more information on saving the configuration, see the ADIC Management Console User Guide. Shut the SNC 5100 down and disconnect the power cord. For each cable attached to the SNC 5100, repeat the following: Remove the cable. Mark what the cable was connected to (for example, SNC 5100 number 3, SCSI channel 1). If the final cable has been removed, then return to the MAP that sent you here, or continue with "Removing and Replacing the Unit". Removing and Replacing the Unit Caution Follow all ESD-sensitive parts procedures while performing this procedure. For ESD information, see "Handling Electrostatic Discharge-Sensitive Parts" on page 81. This procedure describes how to remove and replace the SNC 5100. Removing the SNC 5100 Step 1. Complete all steps in "Before Removing or Replacing the Unit" on page 82. After the final cable has been removed, pop off the plastic rack-mount bezel, if installed on your unit. Unscrew the four 4-40 x 3/8" screws that hold the units to the rack bracket. Step 3. 6-00020-02 Removing and Replacing the Unit 83 SNC 5100 Step 4. Step 5. Remove the rack bracket from across the width of the 19" rack by unscrewing the two 10-32 x 5/8" screws. Slide the unit out of the rack. Replacing the SNC 5100 Step 1. Remove the SNC 5100 from the protective bag. [. . . ] EXCEPT FOR THE EXPRESS LIMITED WARRANTY STATED ABOVE, ADIC MAKES NO WARRANTIES, EXPRESS OR IMPLIED, FOR THE SOFTWARE, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. This License commences on the Effective Date and will continue in perpetuity unless Licensee fails to comply with any conditions of this License. If Licensee breaches, ADIC may, after allowing Licensee a reasonable time to cure its default, terminate this License upon written notice to the Licensee. Within 30 days after termination of this License, Licensee will certify, in writing, to ADIC, that Licensee has discontinued the use of all Software and returned to ADIC the original and all copies of the Software and Documentation in any form maintained by Licensee. [. . . ]