User manual QUANTUM TC2201E

[. . . ] 1 Remove the TC2201E from the protective bag. 2 Attach the stick-on feet to the bottom of the unit. 3 Place the TC2201E on the table or desktop. 0 Installing the TC2201E in a Rack Before beginning installation, review the following installation procedure. When familiar with the installation procedure, follow the steps indicated to mount the TC2201E into a standard 19" rack using the provided mounting materials, which include: · · · One TC2201E Two ear brackets A bag of mounting screws (8 #M6x12 Phillips screws and 4 #6-32x. 312 Phillips screws) 0 Required Tools 0 The following tool is required for installation: · Phillips screwdriver (#2 size) Installing the TC2201E With Ear Brackets 0 To install the TC2201E with ear brackets: 1 Remove the TC2201E from the protective bag. 4 Unpacking the Box Quantum TC2201E Installation Instructions Document 81-81449-01 A01 July 2005 2 Determine where the TC2201E will be mounted. [. . . ] Be sure to insert the cable connectors in the proper orientation. SCSI Connection 0 The TC2201E can support Fast/Ultra160 Narrow/Wide SCSI, depending on the specific configuration. The TC2201E is factory configured to support LVD/Single-Ended buses. Two VHDCI 68-pin D-shell, P-type connectors are located on the rear panel of the unit, allowing the unit to be attached at the end of up to two SCSI buses. The TC2201E must always be installed at the end of SCSI buses. The TC2201E supplies termination power (TERMPWR) to each SCSI bus. An internal self-resetting fuse in the TERMPWR will reset after a fault is cleared. Connecting the TC2201E 9 Quantum TC2201E Installation Instructions Document 81-81449-01 A01 July 2005 Figure 9 High Density SCSI Cables Warning: During attachment of high density SCSI cables, please note the orientation (as shown in Figure 2-11) of the high density SCSI port connectors on the back panel of TC2201E. Failure to maintain appropriate orientation of the cables to the SCSI port connectors can result in damage to the SCSI port connectors on the TC2201E. Do not plug HVD devices to an LVD/SE bus. Failure to heed this caution may result in severe damage to equipment. SCSI ports on the TC2201E are not hot-pluggable. Power off the TC2201E whenever connecting/disconnecting the SCSI cables. Caution: Caution: Any SCSI cables used with the TC2201E series product must meet SCSI 2 standards and must be LVD rated (specifically low noise cabling). The cables should be rated at 24 Ohm impedance and should have a VHDCI 68pin . 8mm D-shell/P-type to Standard 68pin SCSI D-shell connector at the end being attached to the TC2201E. The type of connector at the other end of the cable will be dependent on the device being connected. Warning: Please be advised that failure to comply with the minimum high density cable specifications can result in damage to the TC2201E or an operational failure of the product. Note: SE is not supported by SCSI-2 protocols. While it is possible to mix SE and LVD devices on the same bus, doing so may result in substantially decreased performance on the bus. 10 Connecting the TC2201E Quantum TC2201E Installation Instructions Document 81-81449-01 A01 July 2005 To connect the TC2201E to a SCSI bus: 1 Power off the SCSI devices on this bus. 2 Connect a SCSI cable to one of the SCSI connectors on the back panel of the unit. The TC2201E should always be installed at the end of the SCSI bus. 3 Make sure that the bus is terminated correctly. [. . . ] The TC2201E is designed to communicate with a terminal or any operating system utilizing a terminal emulator. The baud rate, data bits, stop bits, parity, and flow control of both the TC2201E and the host system must use the same settings. Figure 12 TC2201E Serial Port Serial port Setting Up Serial Port Communications 0 Leave the TC2201E turned off until you have set up the serial port communications on your host computer, unless serial I/O was previously established and is currently running. The TC2201E is designed to communicate with a terminal or any operating system utilizing a terminal emulator. For example, Windows 9x, NT 4. 0, or Windows 2000 operating systems can use Hyper terminal. [. . . ]