User manual QUANTUM TRAV40

[. . . ] 3 Important Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Using The Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Chapter 3 Operation and Maintenance 13 Loading and Unloading Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If your computer has only one IDE port: If your computer has only a single IDE port (see figure 3) it is probably being used by the hard disc drive. You should not attach your tape drive to an IDE port that is being used by a hard disc or a sound card. In this situation, before you can install the tape drive, you must purchase an ATAPI host adapter that provides a second IDE port. You will also need a second IDE cable for the tape drive. After installing the host adapter, set the master/slave jumpers. M M O R --R D D C C CD-ROM configured as "Master" 6 Quantum Travan 40 GB Internal Storage System Installing the Drive Installation Procedure Figure 3 Existing computer with only one IDE port (hard disc attached to primary port) r te d pu oar mb Co ther Mo d d ar H a sc i sc D D Primary IDE port Since there is no secondary IDE port, you must purchase an ATAPI host adapter that provides two ports 2 Set the master/slave jumpers Will the tape drive be sharing the secondary IDE port with any other devices?If a compatible ATAPI device, such as a CD-ROM, is already attached to your secondary IDE port (see figure 2) make sure that the existing ATAPI device is configured as a "master. " Configure the tape drive as a "slave, " (see figure 4). Note: Do not attach your tape drive to an IDE port that is being used by a hard disc or a sound card. If your tape drive will be the only device on the IDE cable, you need to configure your tape drive as a "master" (see figure 4). If your IDE cable supports "Cable Select, " configure the drive for "Cable Select" (see figure 4). The second ATAPI device must also be configured for "Cable Select. " Quantum Travan 40 GB Internal Storage System 7 Installing the Drive Installation Procedure Figure 4 Second ATAPI Device Configured for "Cable Select" 3 Attach or remove mounting brackets Are you mounting the drive in a 3. 5-inch or 5. 25-inch drive bay?If you are mounting the drive in a 5. 25-inch drive bay and your drive did not come with brackets already attached, you must attach mounting brackets to each side of the drive (see figure 5). If you are mounting the tape drive in a 3. 5-inch drive bay, you may need to remove the mounting brackets from each side of the drive. 8 Quantum Travan 40 GB Internal Storage System Installing the Drive Installation Procedure Figure 5 You may have to remove the mounting brackets Drive-activity light / Eject button 4 Mount the drive Slide the drive into an unused drive bay until the bezel is flush with the front of the computer. The Drive-activity light/Eject button should be on the upper left (see figure 6). Secure the drive using four mounting screws. Do not overtighten the screws. Figure 6 The DriveActivity Light/Eject Button Should Be On 5. 25-inch drive bay 3. 5-inch drive bay Drive-activity light / Eject button Drive-activity light / Eject button Quantum Travan 40 GB Internal Storage System 9 Installing the Drive Installation Procedure 5 Attach your tape drive to the secondary IDE port Are any other devices attached to your secondary IDE port?If you already have a CD-ROM or other device attached to your secondary IDE port, attach the tape drive to the middle connector on the IDE cable (see figure 7). Note: Do not attach your tape drive to a cable that is already being used by a hard disc or a sound card. Figure 7 If a CD-ROM is Attached, Attach the Tape Drive to the Middle Connector d aarr H sscc H i D D r te rd pu oa m rb Co the o M -D D CM CM O O R R Primary IDE port Secondary IDE port TA PE Pin 1 (typical) If no other devices are attached to your secondary IDE port, use a new 40-pin IDE cable to attach the tape drive to the secondary IDE port (see figure 8). 10 Quantum Travan 40 GB Internal Storage System Installing the Drive Installation Procedure Figure 8 Use a Mew 40-Pin IDE Cable dd aar H sscc H i D D r te rd pu oa m rb Co the o M TA PE Primary IDE port Secondary IDE port Stripe on cable Pin 1 (typical) In either case, make sure that pin 1 on the tape drive (located next to the power connector) is connected to pin 1 on the IDE cable and on the IDE port connector. Pin 1 on the IDE cable is indicated by a stripe on the edge of the cable. 6 Connect the power cable Connect a 4-pin power cable to the back of the tape drive (see figure 9). If all the power cables in your computer are being used by other devices, you can purchase a Y-shaped power-cable splitter from your computer dealer. Figure 9 4-Pin Power Cable Connection Quantum Travan 40 GB Internal Storage System 11 Installing the Drive Using The Tape Drive 7 Check all cables in your computer system Make sure that no cables have loosened during the installation. Make sure that all cables are routed so that they will not bind or become crimped when you replace the cover of your computer. 8 Reinstall your computer cover Your new tape drive is ready for use. However, you may need to install drivers for your operating system, as described in step 9. 9 Install drivers (Windows systems only) The first time you restart your computer after installing the Travan 40 tape drive, the Windows operating system will try to identify the drive. [. . . ] Try a different cartridge--preferably one that has never been used. Make sure you are using the correct type of tape cartridge (see table 1). You cannot use TR-1, TR-2, TR-3, TR-4, or QIC-80 tapes with this drive. Check to make sure all cables are securely connected and all jumpers are set appropriately. [. . . ]