User manual RANE CP 64S

[. . . ] OPERATORS MANUAL CP 64S COMMERCIAL PROCESSOR PAGING ZONE ASSIGN PAGE 1 PAGE 2 12 12 RMT 1&2 RMT 1&2 2 0 4 LEVEL ZONE 2 4 8 10 2 0 10 6 8 2 0 PROGRAM INPUT LEVELS LINE 1 4 6 8 10 2 0 10 ZONE 1 DUCKER DEPTH PROGRAM SELECT L2 L3 L1 P 2 ZONE 2 LEVEL 4 6 8 0 10 ZONE 1 LEVEL 4 2 6 8 0 10 12 6 0 6 12 · · · · ZONE 2 + ZONE 1 6 LINE 2 4 6 8 2 LINE 3 4 6 8 0 10 2 PRIORITY 4 6 8 0 10 DUCKER DEPTH PROGRAM SELECT L2 L3 L1 P CP 64S COMMERCIAL PROCESSOR OFF ON RMT SIG OL OFF ON RMT SIG OL ACTIVE ACTIVE 40 100 250 630 1. 6k 4k 10k 40 100 250 630 1. 6k 4k 10k POWER QUICK START If you were the type that cheated on school book reports by just skimming through the reading assignments, then this section is for you!It gives you not quite enough information to really know what you're doing. But, if you follow the recommended set up procedure, you should get at least a "B. " Keep the amplifiers and the CP 64S turned off until all connections are made. INTERNAL SETTINGS Access to the following internal controls requires removal of the top cover. [. . . ] Access to these controls is only required once before initial system setup. Do this before the CP 64S is installed in a rack or wired into a system. Make sure the power cable is unplugged before removing the top cover to gain access. Refer to the diagram below for control locations. There are five internal switches related to the two Page Inputs. The dot on the circuit board shows the factory default: 1 Page 1 Phantom Power 15VDC Default: OFF 2 Page 2 Phantom Power 15VDC Default: OFF 3 Page Priority P1, NO, P2 Default: P1 4 Zone 1 Page Sum Pre- or Post-VCA Default: Pre-VCA 5 Zone 2 Page Sum Pre- or Post-VCA Default: Pre-VCA 1 2 Phantom Power is available for both Page Inputs. If phantom power is required for the intended microphone, then set the appropriate switch to ON. If a Paging Input Mic / Line pad switch is set to LINE, Phantom Power is automatically defeated. 3 Page Priority Assign allows you to select one of the Page Inputs as a Priority Page Input. The Priority Pager overrides the non-priority Pager in the Zone(s) it is assigned. Note that the non-priority Pager may still broadcast in any Zone that the Priority Pager is not assigned to or not currently broadcasting in. Set the switch to P1 if you wish Page 1 to have priority over Page 2. If you wish Page 2 to have priority over Page 1, set the switch to P2. If NO is selected, neither Paging Input has priority and both Pagers may be active at the same time. This allows the Paging Inputs to mix for applications like karaoke or PA. If a Page Input is used for emergency paging, set it as the Priority Pager. 6 1 3 2 7 8 45 Manual- 4 5 The Zone 1 Page and Zone 2 Page switches allow you to sum Page signals with Program signals "Pre" (before) or "Post" (after) the VCA. The VCA is used for Zone Level control and Limiting. Therefore, if you require the Page Level to be controlled independent of the Program Level, set the switch for that Zone to "Post. " This is the desired setting for emergency paging. If a unit is located far from the CP 64S or is of a type that might create grounding problems, isolation transformers should be used. When operating cross-coupled line drivers unbalanced (i. e. , any CP 64S Output), it is essential to ground the (­) pin. The four stereo Program Inputs connect to RCA jacks. The same guidelines given above for unbalanced operation apply to these Inputs. [. . . ] This ensures the level in a Zone will never be louder than the maximum level you just set. If you wish one of the Zones to have a lower maximum loudness, lower the Zone Limiter threshold accordingly. Turn the Zone Level controls down to a comfortable listening level. Note that with the Paging Zone Level set to minimum, you will not hear the following Page. [. . . ]