User manual RAYMARINE C-SERIES DISPLAY NEW FEATURES GUIDE
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual RAYMARINE C-SERIES DISPLAY. We hope that this RAYMARINE C-SERIES DISPLAY user guide will be useful to you.
Lastmanuals help download the user guide RAYMARINE C-SERIES DISPLAY.
Manual abstract: user guide RAYMARINE C-SERIES DISPLAYNEW FEATURES GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] C-Series Display New Features
Document number: 81298-1 Date: January 2007
C-Series New Features
Trademarks and registered trademarks
Autohelm, HSB, Raymarine, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are registered trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited (registered in all major marketing territories). AST, Autoadapt, Auto GST, Autoseastate, Autotrim, Bidata, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, Raystar, ST40, ST60, Seaclutter, Smart Route, Tridata and Waypoint Navigation are trademarks of Raymarine Limited. Navionics is a registered trademark of Navionics Company, Italy. [. . . ] Arrows at either end of the bar indicate current steer direction.
Active waypoint
Bearing marker
Steer direction
· In heading mode, the bearing marker is RED. · In COG mode, the bearing marker is GREEN. · When you use the compass bar with an active waypoint, the bearing marker is BLUE and the active waypoint symbol indicates the bearing to your waypoint.
Turning the compass bar on and off
You turn the compass bar on and off from the data toolbar. Use the DATABAR softkey to turn the compass bar on or off. Table 3-1: ON COMPASS OFF DATABAR Softkey Options Displays the standard databar, at the top or side of the screen depending on your setup options. Replaces the standard databar with the compass bar, displayed along the top of the screen. Removes both the databar and the compass bar from your display.
8
C-Series Display New Features Note: When the compass bar is displayed the transducer icons remain visible in the top-right
section of the screen.
Compass bar setup
The compass bar is set to open in heading mode. To change this setting, press the MENU button and go to the Databar Setup menu where you can select either Heading or COG.
Note: If MOB is activated while the compass bar is open, the compass is replaced with the
MOB toolbar. The compass bar returns when you cancel the active MOB.
3. 2 Graphical engine data
You can now display engine tilt and trim data, and data for up to four engine-driven electricity generators (gensets). You may need to set up a new page (or modify an existing page set) for this data as an engine application window is not included in the preconfigured page sets.
To set up an engine data page
1. Select the page set you want to edit by pressing its corresponding softkey. Highlight your preferred page layout and press OK. In the application list, highlight engine and press OK. Refer to the C-Series Reference Manual for more details on setting up page sets.
Engine tilt and trim
To display engine tilt or trim data: 1. Press the MENU button to open the Setup screen. In the Data Groups window, select Engine. Select Engine Tilt or Trim Tabs.
Genset data
To display genset data: 1. In the Data Groups window, select Genset.
Chapter 3: Graphical Data
9
For a list of the data you can display for each genset, see Table 3-2, Genset Data
Options.
Table 3-2:
Data
Genset Data Options
Data type Data range
Speed Total hours Coolant temperature Fuel temperature Oil pressure
Numeric or gauge Numeric Numeric or gauge with numbers Numeric or gauge Numeric or gauge with numbers Numeric Numeric or gauge with numbers Numeric or gauge with numbers Numeric Text Numeric or gauge
-- -- 0150ºC 0300ºF 0150ºC 0300ºF 0100 PSI 07 bar 0750 KPa -- 824V 824V -- -- 0100%
Fuel rate Battery voltage Average line voltage Average AC frequency Status Load
To change the number of gensets
The default number of gensets is one. You can configure the unit to display data for up to four gensets: 1. Select Number of Gensets.
10
C-Series Display New Features
Chapter 4: Autopilot Control
11
Chapter 4: Autopilot Control
If you have a Raymarine autopilot installed, you can access some of its functions from the C-Series display unit. WARNING:The autopilot functions available on the C-Series display unit do not replace the autopilot control head. You must have a pilot control head installed before you enable or engage the autopilot.
Emergency disengage
You can disable the autopilot using the power key. [. . . ] You can also access the password entry screen by pressing EDIT CHANNEL ACCESS then CHANNEL ENABLED/LOCKED.
To change an existing password
1. Press the EDIT LOCKOUT PASSWORD softkey. Enter your old password, then the new password and hint.
To block a channel
On the Sirius Radio Control screen: 1. In the Channel List, select the channel you want to block. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RAYMARINE C-SERIES DISPLAY
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual RAYMARINE C-SERIES DISPLAY will begin.
