User manual RAYMARINE RAYSTAR 112LP INSTALLATION GUIDE

[. . . ] It is the user's responsibility to exercise common prudence and navigational judgement, and this device should not be relied upon as a substitute for such prudence and judgement. Package Contents Checking your Raystar 112LP Package The Raystar 112LP package contains the following standard items: 1. Screws (M4) for pole mount attachment (x2) 6. Installation Guide including Warranty document Items Missing? If any of the above items are missing or damaged, please contact your Raytheon dealer or our Product Support Department to obtain replacement parts. Please note that missing or damaged items cannot be replaced without proof of purchase. Registering this Product Once you have checked that you have all of the listed components, please take the time to complete the warranty document and return it to your national distributor. [. . . ] While planning the location for the receiver, consider finding a convenient pathway for running the interconnecting cable which will connect the GPS receiver to the GPS display unit or to the rest of an integrated system. Ideally the cable should be run in a manner so that it can be hidden from view and, if possible, be in a direct path to the point of connection. It is important to keep the cable separated from other shipboard cables as much as possible to prevent interference pick-up. Note: Mounting on the mast of a sailboat is not recommended Raystar 112LP GPS Transducer Installation Surface Mounting 1. Select a suitable area which allows access to the underside of the mounting surface for fixing and, using the template supplied in this document, carefully drill the two 6mm (0. 25in) fixing holes marked. If the cable is to pass through the mounting surface drill the 6mm (0. 25in) or 19mm (0. 75") centre hole depending on whether the plug has to pass through the surface or not. If the cable is to exit from the side of the GPS above the mounting surface then remove the two plastic tabs (1) obstructing the cable channel. Note: Failure to remove the plastic tabs from within the cable channel could result in cable damage 3. Screw the supplied brass studs (2) into the underside of the receiver. Stick the supplied gasket (3) to the mounting surface ensuring the holes match and pass the cable through the centre hole or the cable exit channel. Carefully position the receiver passing the studs through the holes in the mounting surface and secure to the mounting surface using the thumb nuts provided (4). 1 2 3 2 3 4 4 D4190-1 Raystar 112LP GPS Transducer Installation Pole/Rail Mounting 1. Screw the pole mount base to a suitable pole or rail mount bracket which has an industry standard 1" 14TPI thread until secure. Pass the cable through the centre hole of the pole mount base (A) or through the cable exit hole alongside the centre hole (B) or insert the cable into the side exit channel (C). Check the cable is positioned correctly and secure the receiver to the pole base using the two screws provided. Note: An optional Rail mount bracket is available from Raytheon (Part No. D360) allowing attachment to hand/guard rails from 19mm (3/4") to 25mm (1in). D4191-1 Raystar 112LP GPS Transducer Installation Connections NMEA Version Connection is made via a 10m (33ft) cable terminated with a moulded 6 pin connector. 3 Screen (0V/ground) 2 Screen (0V/ground) 4 Yellow (NMEA out)) 1 Red (Power ) 6 Brown (RTCM in) 5 Green (NMEA in) D4192-1 SeaTalk Version Connection is made via the 10m (33ft) cable with bare ends suitable for connection to an existing SeaTalk bus. Red (12V) Yellow (SeaTalk input/output) Brown (RTCM in) Green (not connected) Screen (0V/ground) D4193-1 NMEA Sentences Output GPGGA, GPGSA, GPGSV, GPGLL, GPRMC, GPVTG, GPDTM, PRAYA. Raystar 112LP GPS Transducer Installation Raytheon Raystar 112LP GPS Receiver Mounting Template 36mm (1. 4in) 18mm (0. 7in) 19mm (0. 75") dia. for NMEA plug 36mm (1. 4in) 18mm (0. 7in) 6mm (0. 25") dia. for cable only Cable Exit Channel 6mm (0. 25") dia. 2 positions D4194-1 Note: Access to the underside of the mounting surface must be available to allow for secure fixing. Raystar 112LP GPS Transducer Installation This page left intentionally blank Raystar 112LP GPS Transducer Installation EMC Installation & Service Guidelines All Raytheon equipment and accessories are designed to the best industry standards for use in the leisure marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but good installation is required to ensure that performance is not compromised. [. . . ] Raytheon equipment should be serviced only by authorised Raytheon service engineers. They will ensure that service procedures and replacement parts used will not affect performance. There are no user serviceable parts in any Raytheon product. Always report any EMC related problem to your nearest Raytheon dealer. [. . . ]