User manual RAYMARINE ST 50 PLUS NAVDATA AND GPS SYSTEM

[. . . ] Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company. . > . . : :. . tohelm@ GPS & NAVDATA Operation and Installation Autohelm Autohelms and SeaTalk are registered Trade Marks of Nautech Limited policy of continuous improvement and updating may change product specifications without prior notice Copyright Nautech 1993 $750 Plus GPS & Navdata Operation and lnstalladon Handbook >_ * Package Contents The following items are included in the ST50 Plus GPS and Navdata packages: 1. Warranty document . -m?, ST50 Plus GPS & Navdata Operation and htaUation *$ -sb Handbook I 8 Contents introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 1: Control Head Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] i Turning Off a Sail Plan Waypoint Selection A Sail Plan waypoint selection can be turned off as follows: 1. Go to the Sail Plan SELection containing the waypoint you wish to turn off. Press V and A momentarily so that the waypoint number flashes. Cycle V or A until the waypoint number changes to `--"(before 1 and after 99). Press V and A momentarily to store the setting. Note: If, for example, you turn a waypoint off at selection 5 out of 10, the vessel will track from 1 to 4 only (a Sail Plan always starts at selection 1). At the end of a Sail Plan At the end of a sail plan route, the display will change to show the bearing and distance to the last waypoint. I1 +. . ' . 5, Chapter 3: Operation 19 Track Control Selecting a Target Waypoint Once the latitude and longitude of a waypoint has been entered, or a sail plan has been setup, the waypoint can then be selected as a target waypoint: 1. Press TRACK to display waypoint information. I 1 0112 131 2. Display the intended target waypoint number UT or LONG) using Vorh. IVote: If the sail plan is selected, the first waypoint will automatically be displayed. LFST 4 N SO"l?Press TRACK to select track control. LBT T 4 N 52"4?l. 9 This defines a track from the current position to the displayed waypoint. ST50 Plus GPS and Navdata Operation and Installation Handbook ;%: `. . ;/ The following navigation information will be displayed on the GPS/Navdata and transmitted onto the SeaTalk bus: l l l l l l Cross Track Error (XTE) Bearing to Target Waypoint Distance to Target Waypoint Target Waypoint Number ETA at Target Waypoint VMG to Target Waypoint Press TRACK to exit track control. Transmission of cross track error (XTE) onto the SeaTalk bus will stop, but waypoint distance, bearing and number will continue. Changing Target Waypoint The target waypoint can be changed as follows: display mode. Press TRACK again to exit track control. Press V and A to select the new waypoint number UT or LONG). Press TRACK to enter track control and select the displayed waypoint as the target. Navigation information relating to the new target waypoint will now be displayed and transmitted onto the SeaTalk bus. Waypoint Advance The GPS/Navdata will automatically advance to the next adjacent waypoint when it is within a predefined distance of a target waypoint. Waypoint advance can also be manually selected to join a route part way through, or simply cut a corner, by advancing the target waypoint. Press TRACK for 1 second to advance the target waypoint by one. The display will show the new target waypoint. This procedure can then be repeated until the desired target waypoint is reached. At the end of a route the GPS/TIavdata will automatically exit track control. Note: In Sail Plan mode waypoint advance is to the next waypoint in the plan (e. g. [. . . ] Your Code Number For future reference, enter your chosen code number into the box below. For obvious reasons, please store this handbook in a safe place. Operation Once only `CODE Lock' entry is invisible once it has been set. 32 SE0 Plus GPS and Navdata Operadon and installation Handbook -Lt `<, a/ On Power-Up Action Didav Shows CAL after 2 seconds and Z146VXX after 4 sec. CODELOCK OFF II - --l--1 I- 3 12-1 2'-`1231 2 3'-' 1234 `1234 FWR ON?10 11 13 14 Press and DISPLAY and TRACK together for 4 seconds Press DISPLAY Press TRACK Press UP or DOWN to select first number Press TRACK to accept number Press UP or DOWN to select second number Press TRACK to accept number Press U P orDOWN to select third number Press TRACK to accept third number Press UP or DOWN to select fourth number Press TRACK to accept code Press TRACK within 10 seconds To exit CODELOCK. press DISPLAY and TRACK together. for 2 seconds 12 Press TRACK If you do not exit `CODELOCK SET' within 10 seconds the display will change to CANCEL CODE. [. . . ]