User manual RAYMARINE ST 80 MAXIVIEW

[. . . ] Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company. ST80 Maxiview Operation & Setup Maxiview ST80 Maxiview Operation and Setup 1 Package Contents 1. Display head installation guide 2 ST80 Maxiview Operation and Setup Contents Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Quick Reference Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · When you exit Multi-line edit, the display returns to the previous Multi-line page. · The display returns to the previous Multi-line page after 8 seconds of keypad inactivity. 28 ST80 Maxiview Operation and Setup Multi-line Setup maxiview 2 DEPTH SPEED 25. 2 FEET 6. 5 KTS 120 M remote HEADING Press to change the current option to the previous option. Press to change the current option to next option. Press these keys together momentarily to switch between 1 and 2 line entries. Press and hold these keys for 4 seconds to delete the current multiline page. Press these keys together momentarily to exit setup and return to the current multiline page. Press and hold these keys for 4 seconds to insert new multiline page before current. Press these keys together momentarily to select next line. D2498-1 · The currently selected line appears in reverse video. · The current page appears in the top right hand corner of the display. · The display flashes for 4 seconds when a page is deleted. After 4 seconds, "PAGE DELETED" is displayed along with the deleted page number. · The next page is displayed when a page is deleted. · The display flashes for 4 seconds when a page is inserted. After 4 seconds, "PAGE INSERTED" is displayed. · A single line at the bottom of the display cannot be changed for a two-line entry. · New pages always consist of 4 lines. Each line displays speed data until it is changed. · Page numbers are automatically renumbered when pages are inserted or deleted. ST80 Maxiview Operation and Setup 29 List of Multi-line Selections The lines of data that can be selected are as follows: Line Data 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Speed Speed over ground Velocity made good to wind Velocity made good over ground Log Trip 1 Average speed Depth Water temperature Apparent wind speed Apparent wind angle True wind speed True wind angle relative True wind angle absolute Beaufort Heading Line Data 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Steer Course over ground Tack course Vessel latitude Vessel longitude Cross track error Velocity made good to wayp't Waypoint number Distance to waypoint Bearing to waypoint Estimated time to arrival Date Time Tide set Tide drift 30 ST80 Maxiview Operation and Setup Multi-line Factory Defaults The factory defaults for the Multi-line pages are: Page 1 Line 1 2 3 4 1 2 1 2 3 4 1 2 3 4 5 1 2 3 4 1 2 1 2 3 4 1 2 3 4 Content Speed Average speed Speed over ground Velocity made good to waypoint Depth Water temperature Heading Steer Course over ground Bearing to waypoint True wind angle True wind speed Tack course Beaufort Waypoint number Cross track error Distance to waypoint Estimated time to arrival Speed Depth Speed Depth Apparent wind angle Apparent wind speed Course over ground Speed over ground Tide set Tide drift 2 3 4 6 7 8 ST80 Maxiview Operation and Setup 31 2. 9 Illumination There are two modes: local and system. Each of these modes has four possible settings: level 3 (brightest), level 2, level 1 and off. Local illumination is used to adjust the lighting of individual display heads -- adjustments will not affect other display heads. System illumination controls the lighting of all display heads in system mode. maxiview LOCAL LAMPS 3 remote Press this key for 1 second from any page to open the illumination display. In local illumination, press this key for 5 second to change to system illumination. In system illumination, press this key for 1 second to return to local illumination. Once the local or system illumination display is active, press this key momentarily to adjust the current setting. Press this key for 1 second to reset the contrast. D2540-1 · Local mode remains active until the power supply is switched off, or the mode is changed to system. [. . . ] · Check the contrast and illumination settings · Faulty LCD module. No exchange of information between SeaTalk instruments · Make sure that the cables are attached securely. · If the problem persists, disconnect your instruments one by one to isolate the faulty unit. Failure of a group of SeaTalk instruments · Make sure that the SeaTalk connections to non-functioning instruments are secure. LCD shows "Code ON" when the power supply is switched on · The CodeLock anti-theft system is operational. Poor character definition · Adjust the contrast. ST80 Maxiview Operation & Setup 61 Chapter 6: EMC and Servicing Guidelines 6. 1 Important information All Autohelm equipment and accessories are designed to the best industry standards for use in the leisure marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but good installation is required to ensure that performance is not compromised. Although every effort has been taken to ensure that they will perform under all conditions, it is important to understand what factors could affect the operation of the product. 6. 2 Installation To avoid the risk of operating problems, all Autohelm equipment and cables connected to it should be; · At least 1m (3 feet) from any equipment transmitting or cables carrying radio signals, e. g. , VHF radios, cables and antennas. [. . . ]