User manual RAYMARINE ST60 CLUB HOUSE WIND

[. . . ] ST60 Club House Wind Instrument Owner's Handbook Document number: 81148_4 Date: 1 April 2004 Raymarine, ST60 and SeaTalk are trademarks of Raymarine Limited © Handbook contents copyright Raymarine Limited 2004 Preface i Preface Important information Safety notices WARNING: Product installation & operation This equipment must be installed and operated in accordance with the Raymarine instructions provided. Failure to do so could result in personal injury, damage to your property and/or poor product performance. WARNING: Electrical safety Make sure you have switched off the power supply before you start installing this product. WARNING: The ST60 Club House Wind is intended only for fixed, shore-based use and is not suitable for use on boats. EMC conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. [. . . ] In the case of SSB radios, the distance should be increased to 7 ft (2 m). · More than 7 ft (2 m) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element. · The equipment is supplied from a separate battery from that used for engine start. Voltage drops below 10 V in the power supply to our products, and starter motor transients, can cause the equipment to reset. This will not damage the equipment, but may cause the loss of some information and may change the operating mode. · Raymarine specified cables are used. Cutting and rejoining these cables can compromise EMC performance and must be avoided unless doing so is detailed in the installation manual. · If a suppression ferrite is attached to a cable, this ferrite should not be removed. If the ferrite needs to be removed during installation it must be reassembled in the same position. Suppression ferrites The following illustration shows typical cable suppression ferrites used with Raymarine equipment. Always use the ferrites supplied by Raymarine. 10 ST60 Club House Wind Instrument Owner's Handbook D3548-6 Connections to other equipment If your Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite MUST always be attached to the cable near the Raymarine unit. 2. 2 Installation procedure As it is not possible to describe procedures for all possible installation scenarios, the procedures given here describe the broad requirements for installing a Wind Vane and ST60 Club House Wind instrument. Adapt these procedures as appropriate, to suit your individual requirement. CAUTION: Where it is necessary to cut holes (e. g. for cable routing and instrument mounting), ensure that these will not cause a hazard by weakening critical parts of any structure. Unpacking Unpack your ST60 instrument and check that the items described in the Preface are present. Each ST60 instrument is supplied with a standard bezel for surface mounting. Optional mounting kits are available for flush mounting and bracket mounting the instrument. If you have ordered the flush mounting option a low-profile bezel and four fixing screws are also provided. Fitting the instruments The ST60 Club House Wind instrument can be installed using one of a number of different mounting options: · Surface mounting. Gives a profile of approximately 0. 95 in (24 mm). Gives a profile of approximately 0. 25 in (6 mm). · Bracket mounting. Chapter 2: Installation 11 ST60 instruments can also be mounted behind a suitably prepared panel, so that just the instrument dial and keys are visible. Surface mounting To surface mount your ST60 instrument (see the Surface mounting illustration): 1. Ensure that: · The selected location is clean, smooth and flat. · There is sufficient space behind the location to accommodate the rear of the instrument and connectors. [. . . ] At the instrument, use the < and > keys to set the pointer to the current wind direction, As you do this, the wind angle screen (on the digital display) shows the wind vane offset angle. Press the key to select the wind speed units screen. Use the < and > keys to select the units you want, either knots ( KTS ) or meters per second ( M /S). 22 ST60 Club House Wind Instrument Owner's Handbook Hold down and set for approximately 2 seconds Entry screen Wind angle Press either or (decrease) (increase) to set the current wind angle Wind speed units Press either or to set the required wind speed units (KTS or M/S) User calibration D4513-1 Leaving User calibration Hold down the and set keys for 2 seconds to save your settings, exit calibration and resume normal operation. 3. 3 Intermediate calibration The intermediate calibration screen enables you to check the instrument software version number. This information is normally required if you request parts or repairs To check the instrument software version number, hold down the for approximately 4 seconds. [. . . ]