User manual RAYMARINE ST60 MULTI

[. . . ] ST60 Multi Instrument Owner's Handbook Document number: 81039-4 Date: 1 April 2004 Raymarine, ST60 and SeaTalk are trademarks of Raymarine Limited © Handbook contents copyright Raymarine Limited 2004 Preface i Preface Important information Safety notices WARNING: Product installation & operation This equipment must be installed and operated in accordance with the Raymarine instructions provided. Failure to do so could result in personal injury, damage to your boat and/or poor product performance. WARNING: Electrical safety Make sure you have switched off the power supply before you start installing this product. WARNING: Although we have designed this product to be accurate and reliable, many factors can affect its performance. [. . . ] Press any other key to leave the contrast-adjust mode. Note: The display will also return to normal operation 7 seconds after the last key press. 1. 8 Pop-up Pilot A Pop-up Pilot facility enables instruments connected to SeaTalk to constantly monitor any changes to the autopilot mode and to the course settings. If one of these parameters changes, the new value is immediately displayed on the ST60 instrument for 5 seconds, after which time the display reverts to the previous display. This facility can be enabled or disabled during User calibration (see Chapter 4, Calibration ). 1. 9 Remote control When it is connected to SeaTalk, the ST60 Multi instrument can be controlled remotely with a SeaTalk Remote Keypad Unit. Remote control of an instrument is indicated by a REMOTE legend on the display, to indicate that the keypad has control. Details on how to use the remote control facility can be found in the SeaTalk Remote Keypad Owner's Handbook. Chapter 2: Maintenance & Troubleshooting 11 Chapter 2: Maintenance & Troubleshooting 2. 1 Maintenance Servicing and safety · Raymarine equipment should be serviced only by authorised Raymarine service technicians. They will ensure that servicing procedures and replacement parts used will not affect performance. There are no user-serviceable parts in any Raymarine product. · Some products generate high voltages, and so never handle the cables/connectors when power is being applied to the equipment. · When powered up, all electrical equipment produces electromagnetic fields. These can cause adjacent pieces of electrical equipment to interact with one another, with a consequent adverse effect on operation. In order to minimize these effects and enable you to get the best possible performance from your Raymarine equipment, guidelines are given in the installation instructions, to enable you to ensure minimum interaction between different items of equipment, i. e. ensure optimum Electromagnetic Compatibility (EMC). · Always report any EMC-related problem to your nearest Raymarine dealer. We use such information to improve our quality standards. · In some installations, it may not be possible to prevent the equipment from being affected by external influences. In general this will not damage the equipment but it can lead to spurious resetting action, or momentarily may result in faulty operation. Instrument Certain atmospheric conditions may cause condensation to form on the instrument window. This will not harm the instrument and can be cleared by increasing the illumination setting to Level 3. Periodically clean your ST60 instrument with a soft damp cloth. Do NOT use chemical and abrasive materials to clean the instrument. Transducer Refer to the Installation and Maintenance instructions supplied with the transducer. 12 ST60 Multi Instrument Owner's Handbook Cabling Examine all cables for chafing or other damage to the outer shield and, where necessary, replace and re-secure. 2. 2 Troubleshooting Preliminary procedures Changes in the electronic environment may adversely affect the operation of your ST60 equipment. Typical examples of such changes are: · Electrical equipment has recently been installed or moved aboard your vessel. · You are in the vicinity of another vessel or shore station emitting radio signals. If you appear to have a problem, first ensure that the EMC requirements are still being met before further investigating the problem. Fixing faults Some data types may not be supported by your system and therefore will not be displayed on your ST60 Multi instrument. [. . . ] · WIND speed units to either knots (KTS) or meters per second (M/S). Setting units With the Units Setup screen displayed, use the key to display each data type in turn and for each, use the track or reset key to select the required unit. Waypoint identity Determines whether waypoints are identified by name (WP NAME) or by number (WP NO). Select NMEA or auxiliary alarm If the ST60 Multi is connected to NMEA, select ON. If the Auxiliary Alarm option is fitted select OFF, to enable the Auxiliary Alarm. Auxiliary alarm enable If the Auxiliary Alarm option is fitted, use this screen to determine which alarms you want to sound at the Auxiliary Alarm. The screen heading shows which alarm you are setting, and when you have set one alarm, press the key to display and set the next alarm. [. . . ]