User manual RAYMARINE ST60+ CLUB HOUSE WIND INSTRUMENT

[. . . ] ST60+ Club House Wind Instrument Owner's Handbook Document reference: 81267-1 Date: December 2005 Raymarine, ST60+ and SeaTalk are trademarks of Raymarine UK Limited © Handbook contents copyright Raymarine UK Limited 2005 i Preface Contents Important information Safety notices WARNING: Product installation & operation This equipment must be installed and operated in accordance with the Raymarine instructions provided. Failure to do so could result in personal injury, damage to your property and/or poor product performance. WARNING: Electrical safety Make sure you have switched off the power supply before you start installing this product. WARNING: Instrument usage The ST60+ Club House Wind instrument is intended only for fixed, shore-based use and is not suitable for use on boats. EMC conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. [. . . ] mast top) is otherwise suitable but not horizontal, make up a suitable wedged packing piece to provide the necessary horizontal surface. 10. 7 in (272 mm) 2. 7 in (68 mm) 21. 2 in (538. 5 mm) 1. 5 in (38 mm) D6495-2 9. 76 in (248 mm) 8 ST60+ Club House Wind Instrument Owner's Handbook There must also be a viable route for the transducer cable to be routed to the instrument. Note: As you will need to manually rotate the Wine Vane as part of the linearization procedure, do not actually fit it in position yet. Instrument CAUTION: Keep the rear of the instrument dry Keep the rear of instrument dry. Failure to observe this caution could result in damage if water enters the instrument through the breathing hole or comes into contact with the electrical connectors. Each instrument must be positioned where: · It is protected against physical damage. · It is at least 20 in (500 mm) from radio receiving equipment. · There is reasonable rear access for installation and servicing. With standard bezel (surface mount) 4. 33 in (110 mm) 0. 93 in (23. 5 mm) 0. 6 in (15 mm) With low profile bezel (flush mount) 4. 90 in (124 mm) ST60+ instrument dimensions 0. 25 in 1. 4 in (6. 50 mm) (35 mm) D8146-1 490 in (124 mm) 3. 54 in (90 mm) diameter 4. 53 in (115 mm) 3. 54 in (90 mm) diameter Chapter 2: Installation 9 EMC installation guidelines All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised. Although every effort has been taken to ensure that they will perform under all conditions, it is important to understand what factors could affect the operation of the product. The guidelines given here describe the conditions for optimum EMC performance, but it is recognized that it may not be possible to meet all of these conditions in all situations. To ensure the best possible conditions for EMC performance within the constraints imposed by any location, always ensure the maximum separation possible between different items of electrical equipment. For optimum EMC performance, it is recommended that wherever possible: · Raymarine equipment and cables connected to it are: · At least 3 ft (1 m) from any equipment transmitting or cables carrying radio signals e. g. In the case of SSB radios, the distance should be increased to 7 ft (2 m). · More than 7 ft (2 m) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element. · The equipment is supplied from a separate battery from that used for engine start. Voltage drops below 10 V in the power supply to our products, and starter motor transients, can cause the equipment to reset. This will not damage the equipment, but may cause the loss of some information and may change the operating mode. · Raymarine specified cables are used. Cutting and rejoining these cables can compromise EMC performance and must be avoided unless doing so is detailed in the installation manual. · If a suppression ferrite is attached to a cable, this ferrite should not be removed. If the ferrite needs to be removed during installation it must be reassembled in the same position. Suppression ferrites The following illustration shows typical cable suppression ferrites used with Raymarine equipment. Always use the ferrites supplied by Raymarine. 10 ST60+ Club House Wind Instrument Owner's Handbook D3548-6 Connections to other equipment If your Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite MUST always be attached to the cable near the Raymarine unit. 2. 2 Installation procedure As it is not practical to describe procedures for all possible installation scenarios, the procedures given here describe the broad requirements for installing a Wind Vane and ST60+ Club House Wind instrument. Adapt these procedures as appropriate, to suit your individual requirement. [. . . ] Dealer calibration also gives access to the Factory defaults screen. This enables you to re-apply the factory settings if you want to reset the instrument to a known operating condition. To commence Dealer calibration, hold down the and set buttons together for approximately 12 seconds, to select the Dealer calibration entry page (see Dealer calibration diagram, sheets 1 and 2). Then momentarily press the < and > buttons to proceed with the calibration. [. . . ]