User manual RAYMARINE ST60+ DEPTH INSTRUMENT

[. . . ] ST60+ Depth Instrument Owner's Handbook Document reference: 81262-2 Date: December 2005 Raymarine, ST60+ and SeaTalk are trademarks of Raymarine UK Limited © Handbook contents copyright Raymarine UK Limited 2005 i Preface Contents Important information Safety notices WARNING: Product installation & operation This equipment must be installed and operated in accordance with the Raymarine instructions provided. Failure to do so could result in personal injury, damage to your boat and/or poor product performance. WARNING: Electrical safety Make sure you have switched off the power supply before you start installing this product. WARNING: Navigational safety Although we have designed this product to be accurate and reliable, many factors can affect its performance. [. . . ] If you appear to have a problem, first ensure that the EMC requirements are still being met before further investigating the problem. Fixing faults All Raymarine products are subjected to comprehensive test and quality assurance programmes prior to packing and shipping. However, if a fault occurs, the following table may help to identify and rectify the problem. Fault Display blank Cause No power supply Remedy Check power supply & ensure instrument is switched on. Check SeaTalk cabling and connector security Check fuse/circuit breaker Check security of SeaTalk connectors. Isolate faulty instrument by disconnecting instruments one by one. Check the security of SeaTalk connectors between functioning and non-functioning instruments No transfer of information between SeaTalk instruments (e. g. Failure of a group of SeaTalk instruments. SeaTalk cable or connector fault SeaTalk cable or connector fault LAST flashing or dashes Transducer cable or Check the condition of the transdisplayed continuously connector fault ducer cable and the security of the (depth greater than 3 ft) connections LAST flashes when under way Aerated water due Ensure reading stabilizes when clear to -boat wakes, of disturbed water. propeller wash etc. Chapter 2: Maintenance & Troubleshooting 9 Technical support Raymarine provides a comprehensive customer support service, on the world wide web and by telephone help line. Please use either of these facilities if you are unable to rectify a problem. World wide web Please visit the Customer Support area of our web site at: www. raymarine. com As well as providing a comprehensive Frequently Asked Questions section and servicing information, the web site gives e-mail access to the Raymarine Technical Support Department and a details of the locations of Raymarine agents, worldwide. Telephone help line If you do not have access to the world wide web, please call our help line. In the USA, call: · +1 800 539 5539, extension 2444 or · +1 603 881 5200 extension 2444 In the UK, Europe the Middle East or the Far East, call: · +44 (0) 23 9271 4713 (voice) · +44 (0) 23 9266 1228 (fax) Help us to help you When requesting service, please quote the following product information: · Equipment type. To find out the software version number of your ST60+ Depth instrument: 1. During normal operation, hold down the depth and alarm buttons for approximately 4 seconds, to display the VERSION screen. Software version D8246-2 2. Note the software version number, then hold down the depth and alarm buttons for approximately 2 seconds, to return to normal operation. 10 ST60+ Depth Instrument Owner's Handbook 11 Chapter 3: Installation This chapter describes how to install the ST60+ Depth instrument, and associated depth transducer. The transducer is fitted in the hull of the vessel and is connected by cable to the rear of the instrument. The actual type of transducer depends on the type of hull in which it is to be installed. For advice, or further information regarding the installation of this equipment, please contact the Raymarine Product Support Department or your own National Distributor. 3. 1 Planning your installation Before starting the installation, spend some time considering the best positions for both transducer and instrument, such that the Site Requirements and the EMC installation guidelines (below) are satisfied. Site requirements Transducer 2. 94 in (75 mm ) diameter 2. 0 in (51 mm ) diameter 2. 94 in (75 mm ) diameter Depth transducer dimensions 0. 19 in (5 mm) 3. 75 in (95 mm ) D8685-1 The transducer types required for the various hull types are as follows: 12 ST60+ Depth Instrument Owner's Handbook Hull material Glass reinforced plastic (GRP) Steel Aluminium Wood Transducer type 31-188-4-02 Through hull plastic M78718 Retractable through hull 31-188-4-02 Through hull plastic M78718 Retractable through hull 31-188-4-02 Through hull plastic M78718 Retractable through hull 31-188-4-02 Through hull bronze M78719 Retractable through hull Other transducer types are also available for specific requirements. For further details, contact your local Raymarine dealer. For accurate depth readings the transducer should be sited within the clear water flow areas indicated by the shaded areas in the following diagram. Sailing vessel Planing power vessel Displacement power vessel Transducer siting D4349-1 The transducer should also: · Be ahead of the propellers (by a minimum of 10% of the water line length). · Be at least 6 in (150 mm) away from the keel (ideally ahead of the keel if a sailing yacht). Chapter 3: Installation · · · · · Be as near as possible to the center line of the vessel. Be clear of other through-hull fittings or projections. Have sufficient clearance inside the hull to fit the nut. Have 4 in (100 mm) of headroom to allow for withdrawal. Be within 10° of the vertical, forward, aft and athwart ships. 13 There must also be a viable route for the transducer cable to be routed to the instrument. 10° maximum Maximum transducer angle D4350-1 Instrument CAUTION: Keep the rear of the instrument dry Keep the rear of instrument dry. [. . . ] Press the depth button to select the Instrument status screen. Press the offset and reset buttons simultaneously to enter adjust mode, then press either offset or reset to set the required status. Note: You must not allocate more than one MASTER depth instrument in any system. D8166-1 Chapter 4: Calibration 31 3. Press the offset and reset buttons simultaneously again, to leave the adjust mode. Note: If a fishfinder is connected to the same SeaTalk system as your ST60+ Depth instrument and is switched on, all ST60+ Depth instruments in the system will display fishfinder depth information from SeaTalk. Under these conditions, a master ST60+ Depth instrument will act as a slave, and in Intermediate calibration, the MASTER legend will change to SLAVE, when not in adjust mode. Leaving Intermediate calibration Hold down the depth and alarm buttons for 2 seconds to save your settings, exit Intermediate calibration and resume normal operation. 4. 4 Dealer calibration The Dealer calibration procedure (see Dealer calibration diagram) enables the following parameters to be set: · User calibration on/off. [. . . ]