User manual RAYMARINE ST70

[. . . ] 9 3. 1Install the instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3. 2Install transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3. 3Final fix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3. 4Commission the instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Place Raymarine equipment and cables more than 7 ft (2 m) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element. Use a power source separate from that used for engine-start. This is important to prevent erratic behavior and data loss which can occur if the engine-start does not have a separate battery. Do not cut or extend cables unless doing so is detailed in the installation manual. · · · · Remember Where constraints on the installation prevent any of the above recommendations: · Always allow the maximum separation possible between different items of electrical equipment. This will provide the best conditions for good EMC performance of the installation. Suppression ferrites Raymarine cables may be fitted with suppression ferrites. These are necessary for correct EMC performance. Any ferrite removed during installation must be replaced as soon as installation is complete. Use only ferrites of the correct type, supplied by Raymarine authorized dealers. Connections to other equipment If Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a Raymarine suppression ferrite MUST always be attached to the cable near the Raymarine unit. EMC Servicing and maintenance · Undue noise and interference may be a symptom of an EMC-related problem. Please report any EMC-related problem to your nearest Raymarine dealer. We use such information to improve our quality standards. To minimize any EMC related problems and ensure the best possible performance form your Raymarine equipment, follow the guidelines given in the installation instructions. · Product documents The following user documents are available to help you install and operate an ST70 instrument controller: · ST70 Instrument Installation Guide (this document). · ST70 Instrument Operating Guide. This is a detailed manual supplied with your ST70 instrument. It contains important commissioning instructions. This provides detailed information regarding SeaTalkng connectivity. Preface vii To the best of our knowledge, the information in the product documents was correct when they went to press. However, Raymarine cannot accept liability for any inaccuracies or omissions in product documents. In addition, our policy of continuous product improvement may change specifications without notice. Therefore, Raymarine cannot accept liability for any differences between the product and the accompanying documents. Product disposal Waste Electrical and Electronic (WEEE) Directive The WEEE Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some of Raymarine's products, we support its policy and ask you to be aware of how to dispose of this product. The crossed out wheelie bin symbol, illustrated above, and found on our products signifies that this product should not be disposed of in general waste or landfill. [. . . ] For safety, your boat must be at dockside before you begin installation. 3. 1 Install the instrument Once you are certain it is safe to proceed, follow the installation procedure below. Fit cable to system connection point and route to ST70 instrument location For SeaTalkng: · · Label both ends of the SeaTalkng cable, and attach it to the backbone or an existing ST70 instrument on your system. Before you connect a transducer to a pod, ensure that you are using the correct type of pod (speed pod for a speed transducer or depth pod for a depth transducer, for example). · Fit the appropriate transducer directly to its corresponding instrument as shown. [. . . ]