User manual RAYMARINE ST80 MASTERVIEW

[. . . ] Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company. ST80 Masterview User's Manual mas terv iew . Masterview ST80 Masterview Operation and Setup 1 Package Contents The ST80 Masterview package contains the following standard items: 1. Masterview display head Sun cover Thumb nuts (2) Fixing studs (2) SeaTalk cable 0. 38m (1. 2ft) Gasket Cue card Installation guide Operation and Setup manual 10. If any of the above items are missing, please contact your Autohelm dealer or our Product Support Department. [. . . ] Press to return to the Waypoint List and save changes. WAYPOINT LIST BELL POINT COWES TAB TOWER · If a target waypoint (identified in the waypoint list by the letter `T') is being tracked, then the edit key is disabled and that particular waypoint cannot be edited. · If the waypoint is used in a route, a message similar to "WP USED IN 4 ROUTES CHANGE ALL?" will be displayed before the changes are saved. EDITWPT 46 ST80 Masterview Operation and Setup Deleting a Waypoint Cycle the display until you come to `Waypoint List' and then follow the instructions illustrated below: Deleting a Waypoint WAYPOINT LIST BEMBRIDGE BOURNMOUTH BOWRING BRACKLESHAM BAY CHERBOURG CHICHESTER 1 abc 2 def 3 ghi 4 jkl 5 mn 6 opq 7 rst 8 uvw 9 xyz ins 0 del Scroll - Use the Navigator up or down key to highlight the waypoint to be deleted or press any alphanumeric key to open the 'Waypoint Search' feature. . . Waypoint Search - Use the Navigator keypad to type in the first character of the waypoint to be deleted. If there are multiple waypoints beginning with that letter, type in additional characters until the required waypoint name is highlighted. EDIT WAYPOINT 1 abc 2 def 3 ghi 4 jkl 5 mn 6 opq 7 rst 8 uvw 9 xyz ins 0 del WAYPOINT LIST N-----------------------------CHERBOURG CHICHCHESTER CHRISTCHURCH LYMINGTON NAB TOWER 4 EDIT WAYPOINT YES or NO DELWPCAT 5 What if the Waypoint is Used in Routes? If the waypoint you want to delete is used in one or more routes, the message `USED IN ROUTE' will be displayed and you will not be allowed to delete it. To delete the waypoint it must first be removed from all routes. ST80 Masterview Operation and Setup 47 Adding Event Marks Event marks can also be added to the waypoint list. An event name is automatically created using the current date, and time, and is preceded with the letters EV. To create an event mark, proceed as follows: Adding an Event Mark WAYPOINT LIST NEW WAYPOINT NAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NEW WAYPOINT NEW WAYPOINT WAYPOINT LIST 4 5 Route Page The Route feature allows you to create, name and store up to 20 routes comprising of up to 50 waypoints from the waypoint list. INS_MARK 48 ST80 Masterview Operation and Setup Creating a Route Cycle the pages in the Navigate Chapter until `ROUTE LIST' is displayed. To create a new route, follow the instructions below. Creating a New Route ROUTE LIST 02 COWES 03 CHERBOURG 04 DOVER 05 ------------------06 ------------------- E E Press the up or down Navigator key to highlight any empty route. ROUTE 05 ---------------------------START 01 END Enter a route name using the Navigator Keypad. 1 abc 2 def 3 ghi 4 jkl 5 mn 6 opq Use these keys to enter data at the current cursor position (e. g. cycle of key 1 is 1, a, b, c, 1 etc. ) Use these keys to insert a space or delete data at the cursor position. Use the multi-directional trackpad keys to move the cursor. 7 rst 8 uvw 9 xyz ins 0 del ROUTE 05 LYMINGTON START 01 END Press the up or down Navigator key to highlight the first waypoint entry (-01). ROUTE 05 LYMINGTON START 01 END 6 Now turn the page and add waypoints as shown NEWROUT2 ST80 Masterview Operation and Setup 49 Adding Waypoints ROUTE 05 LYMINGTON START 01 END 1 abc 2 def 3 ghi 4 jkl 5 mn 6 opq 7 rst 8 uvw 9 xyz 0 Press the first character of the required waypoint name. The display will jump to the waypoint list which can be scrolled using the Navigator Keypad cursor keys (see below). SELECT WP ---------------------------BROWNDOWN BEMBRIDGE LED CULVER SPIT DEAN ELBOW Waypoint Scroll Press and hold the up or down Navigator key to scroll the list of waypoints. OR SELECT WP SH----------------------SANDOWN BAY SHANKLIN THE NEEDLES YARMOUTH 1 abc 2 def 3 ghi 4 jkl 5 mn 6 opq 7 rst 8 uvw 9 xyz 0 Waypoint Search Use the Navigator keypad to type in the next character of the required waypoint. If there are multiple waypoints beginning with that letter, type in additional characters until the required waypoint name is highlighted. ROUTE 05 LYMINGTON START 01 SHANKLIN 02 END Press this key to insert the highlighted waypoint to the route and return to the route contents display. Repeat the above actions from stage 2 above to add further waypoints to the route. Once all the waypoints have been inserted, press the exit key to return to the route list display. ROUTE 05 LYMINGTON START 01 SHANKLIN 02 VENTNOR END ROUTE LIST 00 02 03 04 O5 ROUND ISLAND COWES CHERBOURG DOVER LYMINGTON FINDWPT 50 ST80 Masterview Operation and Setup Deleting Waypoints from a Route Cycle the Navigate Chapter until the `Route List' is displayed. Deleting a Waypoint from a Route ROUTE LIST 02 COWES 03 CHERBOURG 04 DOVER 05 LYMINGTON 06 ------------------- E Highlight the required route using the Navigator Keypad Highlight the waypoint to be deleted using the Navigator up or down key. Press the delete key to display the 'Delete Waypoint?' pop-up. Press to remove the selected waypoint from the route. ROUTE LIST 02 COWES 03 CHERBOURG 04 DOVER 05 LYMINGTON 06 ------------------- E ROUTE 05 LYMINGTON START 01 SHANKLIN 02 VENTNOR END ROUTE 05 LYMINGTON START 01 SHANKLIN 02 VENTNOR END ROUTE 05 LYMINGTON START 01 SHANKLIN 02 VENTNOR END ROUTE 05 LYMINGTON START 01 SHANKLIN 02 VENTNOR END ROUTE 05 LYMINGTON START 01 SHANKLIN 02 END What if I Decide that I Don't Want to Delete the Waypoint? Providing you have not already deleted the waypoint, simply press the NO key instead. Press the exit key to return to the `Route List' page. REMWPT ST80 Masterview Operation and Setup 51 Inserting a Waypoint in a Route Cycle the Navigate chapter until `Route List' is displayed. Inserting a Waypoint in a Route ROUTE LIST 02 COWES 03 CHERBOURG 04 DOVER 05 LYMINGTON 06 ------------------- E Highlight the required route using the Navigator up or down key. ROUTE LIST 02 COWES 03 CHERBOURG 04 DOVER 05 LYMINGTON 06 ------------------- Press the 'Edit Route' key E ROUTE 05 LYMINGTON Highlight the point at which you want to insert a waypoint using the Navigator Keypad up or down key. ROUTE 05 LYMINGTON START 01 02 SHANKLIN 03 VENTNOR Tracking to a Route Selected from the Route List Cycle the navigate Chapter until the `Route' page is displayed. Selecting a Route ROUTE NO ROUTE SELECTED ROUTE SELECT 0I 02 03 04 05 06 ROUND ISLAND A --------------------------E CHERBOURG DOVER NAB TOWER CALAIS Use the up or down key to highlight the route you require. ROUTE SELECT 03 CHERBOURG 04 DOVER 05 NAB TOWER 06 CALAIS 07 YARMOUTH 08 LYMINGTON ROUTE 05 NAB TOWER 01 SAND FORT BEARING 120 RNG 0. 5NM ROUTE 05 NAB TOWER 01 SAND FORT 5 6 SELROUTE BEARING 120 RNG 0. 5NM Press the 'Track' key to begin tracking the selected route. ROUTE 05 NAB TOWER TRACKING 01 SAND FORT BEARING 120 RNG 0. 5NM INSERTWP Press the insert key to insert a new waypoint. A space for the waypoint will be created before the highlighted point. Insert a waypoint from the Waypoint List as described in section 5. 2 'Adding Waypoints'. 5 52 ST80 Masterview Operation and Setup Waypoint Advance When a route is being tracked, you can advance to the next waypoint by selecting the `Route' page and pressing for 1 second. Deselecting a Route A route can be deselected by highlighting route `00' or an empty route (identified by the letter `E'). Deselecting a Route ROUTE SELECT ROUTE SELECT Reversing the Direction of a Route The direction of a route can be reversed so that you can make a return journey. Go to the `Route' page and go to `Route Select'. Select a route to be reversed using the Navigator up or down key. Press (reverse route key) ­ the letter `R' appears to the right of the route name. [. . . ] · Make sure that the SeaTalk cables are not damaged. Display is blank - keypad illuminated · Check the contrast and illumination settings · Faulty LCD module. No exchange of information between SeaTalk instruments · Make sure that the cables are attached securely. · If the problem persists, disconnect your instruments one by one to isolate the faulty unit. Failure of a group of SeaTalk instruments · Make sure that the SeaTalk connections to non-functioning instruments are secure. LCD shows "Code ON" when the power supply is switched on · The CodeLock anti-theft system is operational. Poor character definition · Adjust the contrast. ST80 Masterview Operation and Setup 153 Chapter 5: EMC and Servicing Guidelines 5. 1 Important information All Autohelm equipment and accessories are designed to the best industry standards for use in the leisure marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but good installation is required to ensure that performance is not compromised. Although every effort has been taken to ensure that they will perform under all conditions, it is important to understand what factors could affect the operation of the product. 5. 2 Installation To avoid the risk of operating problems, all Autohelm equipment and cables connected to it should be: · At least 1m (3 feet) from any equipment transmitting or cables carrying radio signals, e. g. , VHF radios, cables and antennas. [. . . ]