User manual RCA DRD502RB

[. . . ] SATELLITE RECEIVER USER'S GUIDE Safety Information TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates important instructions accompanying the product. WARNING To reduce risk of fire or shock hazard, do not expose this receiver to rain or moisture. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol indicates "dangerous voltage" inside the product that presents a risk of electric shock or personal injury. Cautions Do not stack electronic components or other objects on top of the DSS® Receiver. The slots on top of the receiver must be left uncovered to allow proper airflow to the unit. [. . . ] Follow the display screen prompts to initialize your new card. Once you have transferred the information to the new card, your old card becomes invalid. Because your specific account information is stored in the access card, power failures should have no effect on your DSS® system. Remote Setup Choose which remote button, DSS1 or DSS2, will control the DSS® receiver. Picture Size The Picture size display screen allows you to choose between a standard TV screen and a Cinema option. A standard TV screen has an aspect ratio of 4:3; the Cinema option has an aspect ratio of 16:9. Data Port Let's you choose whether the low speed data port is used for low speed data or communicating with the Home Control Base accessory. See the Home Control section in this book for more information. Audio Language When you select Audio Language from the Options menu, the Audio Language display screen comes up. Point to the audio language or audio type you want and press MENU·SELECT. The DSS® system will then automatically set the audio program to the selected audio program type when that type is available. There are two ways to change the audio: · · Press ALT AUD on the remote to temporarily change the Audio program while tuned to the current channel. Point to Audio Language from the Options menu and press MENU·SELECT to set the default Audio Language. Alternate Data Selects from among the available data on the current channel. 45 The Menu System The Dish Pointing Menu Screen Follow these steps to obtain your dish pointing coordinates: 1. Turn on your television and satellite receiver. Tune your television to the satellite receiver's output channel. Press MENU·SELECT on the remote or front panel to bring up the Main menu. Use the arrows to highlight the "Dish Pointing" option, and then press MENU·SELECT to access the dish pointing screen. NOTE: The menu screen that you see may be slightly different from the one pictured here. 5. Use the arrows on the remote or the front panel to highlight "Zip Code" and then press MENU·SELECT. Enter the zip code for the dish installation location. Record the elevation and azimuth numbers below. Elevation ___________ Azimuth __________ Elevation is the up/ down angle that the dish is pointed. Azimuth is side to side direction that the dish is pointed. You only need to use one of the available methods to find your dish pointing coordinates. If you know the zip code for the locality where the dish is being installed, use that. 46 The Menu System Using the On-Screen Signal Meter The signal strength meter is used to determine whether or not you are receiving the satellite signal, and it also indicates the strength of the satellite signal. Follow these steps to bring up the on-screen signal meter: 1. [. . . ] Price Qty Total Self-Installer's Kit contains cable and hardware to install the dish and connect the system. 50 feet 75 feet 100 feet S-Video Cable 12 feet Weatherproof "F" Connector (2) TVRO Bullet Amplifier POWER DSS1 DSS2 TV GUIDE FETCH MENU WHO ELE C CLEAR INFO CH+ ALT. AUD MUTE CH- GO BACK 1 4 7 INPUT 2 5 8 0 3 6 9 ANTENNA Remote Control replaces a lost remote. Or, order a second remote for convenience. Self-Installer's Kit Remote Control Home Control Kit Lamp Module 2-Prong Appliance Module 3-Prong Appliance Module T S VOL VOL HCDSS10 Home Control Kit contains a Data Interface that connects to the DSS® receiver, and a lamp module. HC10LM Lamp module lets you control incandescent lamps. [. . . ]