User manual REMINGTON FIVE

[. . . ] Owner's Owner's Manual for: Remington Model Five Bolt-Action Rimfire Rifle Manual PAGE 2 . . . . . . . . THE TEN COMMANDMENTS OF FIREARM SAFETY IMPORTANT! READ ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL BEFORE USING THIS RIFLE PAGE 5 . . . . . . . . IMPORTANT PARTS OF THE FIREARM PAGE 10. . . . . . . . OPERATING INSTRUCTIONS PAGE 14. . . . . . . . CLEANING INSTRUCTIONS PAGE 15 . . . . . . PARTS AND SERVICE 1 Safety is Critical to Performance. A superbly crafted gun is only as good as the hands that hold it. Shooting accidents are often caused by careless oversights such as failing to control the direction of the muzzle, failing to fully engage the safety, leaving ammunition in the chamber or using improper loads. These oversights can result in the destruction of life, limb or property. There's no calling back a bullet once it's been fired, so it's critical that you know the principles of safe gun handling and storage before you ever take your new Remington firearm out of the box. [. . . ] With proper care and if used in accordance with the Ten Commandments of Firearm's Safety and this owner's manual, your rifle should give you many years of dependable use and enjoyment. The following picture depicts the main parts of a Model Five rimfire bolt-action rifle and will aid in understanding the instructions in this Owner's Manual. BOLT-ACTION SAFETY MECHANISM STOCK MID SIGHT FRONT SIGHT MUZZLE MAGAZINE CLIP TRIGGER TRIGGER GUARD SLING STUD SLING STUD BARREL This picture shows the main parts of a Remington Model Five bolt-action rifle. The picture will aid in understanding the instructions in this book. 5 The Safety Mechanism The safety mechanism is located on the right sight of the receiver just behind the bolt handle. (See Picture 1). Picture 1 Note: The safety mechanism cannot be engaged in the "safe" position unless and until the rifle is cocked. To engage the safety mechanism in the "safe" position, pull the safety to its most rearward position, covering the red indicator dot on the stock. (See Picture 2). Picture 2 "SAFE" Position 6 The Safety Mechanism (cont'd) To place the safety mechanism in the "fire" position, push the safety fully forward, exposing the red indicator dot on the stock. The rifle is now ready to fire by pulling the trigger. (See Picture 3). Picture 3 "FIRE" Position WARNING The firearm will fire when the trigger is pulled and the safety mechanism is in the "FIRE" position if the bolt is installed in the receiver. The Locking Device This firearm was originally sold with a key-operated locking device to assist the owner in protecting against unauthorized use. These are storage, locking devices and the firearm should be unloaded when stored or not in use. Using a locking device cannot substitute securing your firearm and ammunition in a separate, locking location. Return the Safety Mechanism to the "SAFE" position. Picture 8 Removal WARNING Before installing or removing the bolt, visually inspect the chamber and receiver to make sure the chamber and magazine are completely empty. Never attempt to install or remove the bolt with a loaded firearm. 1. After inspecting your firearm to insure it is not loaded, move the Safety Mechanism to the "FIRE" position 2. Raise the bolt handle with your right hand. With the bolt handle fully raised, use your left hand to pull the trigger and hold it to the rear. Keeping the trigger pulled fully to the rear, pull the bolt to the rear and out the receiver. (See Picture 10). Picture 10 WARNING The bolt has been fitted at the factory to assure proper head space when used with this particular rifle. Never interchange bolts from one rifle to another as this may affect head space leading to a potentially hazardous situation. If your bolt is damaged or lost, return your rifle to the factory for replacement with a properly fitted bolt. 9 External Control Parts (cont'd)) THE TRIGGER: The trigger mechanism has been preset at the factory. Never alter or modify the trigger or firing mechanism. (See Ninth Commandment of Firearms Safety. ) THE BARREL: Some of the metal parts of your rifle have had a rust preventative compound applied at the factory to protect the metal during shipment. Before shooting your rifle for the first time, you must clean the anti-rust compound from the barrel, receiver, breech bolt mechanism, and the action/chamber areas. To clean the barrel, refer to the Cleaning Instructions in this Owner's Manual. Operating Instructions Model Five rifles are manufactured with a 5-round detachable box magazine. [. . . ] Avoid applying too much lubricant - - only a light film is necessary. Picture 18 WARNING Never attempt to take your rifle apart further than as set forth in the Owner's Manual. If further cleaning, service or repairs are needed, take your rifle to a competent gunsmith or return to Remington for service. 14 PARTS AND SERVICE To Order Parts ALL PARTS ARE SUBJECT TO A $10. 00 CHARGE FOR SHIPPING AND HANDLING. Some parts are restricted and may only be installed by returning the rifle to us. When ordering parts, please state the Model, Gauge, Serial Number, and Finish Color. [. . . ]