User manual REMINGTON UNDER SHOTGUN

[. . . ] Owner's Owner's Manual for: Remington Premier® Over and Under Shotgun Manual PAGE 2 . . . . . . . . THE TEN COMMANDMENTS OF FIREARM SAFETY IMPORTANT! READ ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL BEFORE USING THIS SHOTGUN PAGE 6 . . . . . . . . IMPORTANT PARTS OF THE FIREARM PAGE 9 . . . . . . . . ASSEMBLY INSTRUCTIONS PAGE 11. . . . . . . . LOADING AND UNLOADING PAGE 12 . . . . . . DISASSEMBLY INSTRUCTIONS 1 PAGE 14 . . . . . . MAINTENANCE INSTRUCTIONS A Tradition of Performance and Safety. In 1816 Eliphalet Remington was confident he could make a flintlock that was as good or better than any he could buy. The barrel he handcrafted set a new standard for firearm accuracy and spawned generations of products that have made Remington® Arms America's leading gunmaker. While performance and style are certainly hallmarks of Remington firearms, one factor ultimately drives their performance. Eliphalet Remington never lost sight of the fact that his rifles were potentially lethal and could kill someone if handled improperly. [. . . ] The inside of both barrels must be clean and free of obstructions. Picture 5 I. Point the muzzle of the firearm in a safe direction. Engage the safety mechanism in the `SAFE' position so the letter `S' SHOWS. Push the rear of the top lever to the right. Rotate the barrel assembly down to open (break) the action. Look through both barrels from the breech end to make sure there no obstructions in them. TO REMOVE AN OBJECT FROM INSIDE A BARREL: WARNING!NEVER try to remove an object from a barrel by loading another shell and firing. This may cause the barrel to burst or a shell to rupture, and cause serious personal injury or death to you and those around you. 1. Remove the barrel assembly following the instructions on Pages 12 and 13. Insert the cleaning rod into the muzzle and lightly tap the rod to free the object. If an object cannot be easily pushed out of the barrel with a cleaning rod, return the firearm to a Remington ® Authorized Service Center III. TO CLEAN THE BARRELS AND CHOKE TUBES FOLLOW THE INSTRUCTIONS ON PAGES 14 AND 15 BEFORE LOADING THE FIREARM: WARNING!Make sure that the inside of both barrels are free of dirt or other objects. 8 Important Parts of the Firearm (cont'd) The Choke Tubes Your Premier Over & Under shotgun is equipped with ProBoreTM choke tubes to allow you to utilize the specific type of choke constriction desired for specific types of hunting or target shooting. A choke tube wrench is also supplied for use when changing or tightening the choke tubes. WARNING! NEVER place your hand over the muzzle when changing or tightening the choke tubes. WARNING!Never attempt to change the choke tubes on a loaded shotgun. TO CHANGE THE CHOKE TUBES: 1. Pull the safety to the `SAFE' position so the letter `S' SHOWS. Open the action and check the chambers to make sure there are no shells in either barrel. Place the choke tube wrench into the choke tube. Turn the wrench counter-clockwise and remove the choke tube. Select the desired choke tube and insert the tube into the barrel. Tighten the choke tube snugly but DO NOT OVER-TIGHTEN. [. . . ] Only install or remove choke tubes with the firearm unloaded, the action open and the trigger block safely engaged. ProBoreTM Chokes Symbols/Markings (This is an option ­ not all Premier® Over and Under shotguns have this feature) The end of the choke tubes are marked with notches to identify the choke construction: / - Skeet // - Improved Modified /// - Light Modified //// - Modified ///// - Improved Cylinder ////// - Full WARNING MAKE SURE YOU FULLY TIGHTEN THE CHOKE TUBE. Shooting with a loose choke tube can cause damage to your shotgun. Additional Information On ProBoreTM Choke Tubes: 1. Only tighten or loosen choke tubes with wrench supplied with shotgun. Never shoot the shotgun with a partially installed choke tube 3. [. . . ]