User manual RENKUS-HEINZ RH-23 DYNA-GARD

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] Any or all of the Control functions can be restricted to authorized operators who have password access; more information on password authorization can be found in the Supervise Mode section of this manual. When you enter Control mode in the main workspace, the directory tree on the left remains the same. CONTROL MODE CONTROL MODE However, notice that the icons themselves have changed. On the left, an On/Off button allows you to switch the amplifier(s) On or select Standby (Off) mode. On the right, a Mute button is labeled with a driver symbol. Below it is a Signal Present indicator. Name On/Off (Standby) button Wink light button Status Indicator Mute button Signal Present indicator Double-click a loudspeaker icon to open its Properties window in Control mode. Notice that the left hand section of the Control mode Properties window is the same as in Connect mode. 21 Users Manual CONTROL MODE 22 On the right side of the Control Properties window, in the upper dark grey section, you will see a frequency response graph. Underneath it are controls for 12 filters. To select a filter, click the button above its white data fields; then either type in your values, use the up-down arrows or scroll with your mouse to adjust the parameters. At the far left is a highpass filter; its lowpass counterpart is at the far right. These filters have three controls: Cutoff Frequency, Type (Bessel, Butterworth, etc. ), and Slope. The pair of filters to the inside are shelving filters, with controls for corner frequency and boost/cut. The All Loudspeakers Control feature also lets you assign Input connections, EQ, Delay and Compression settings for all the loudspeakers in the system at one time or adjust their sound level with just one control. It's a great time saver. CONTROL MODE 24 Double clicking on the Icon will open the Connect Properties folder. Notice that the All Loudspeakers Connect window shown here is very similar to the one for individual loudspeakers except for the lack of level meters and CobraNet channel selection facilities. The All Loudspeaker Control window is highly similar to the one for individual loudspeakers except for the lack of meters and the addition of a row of Group Assign boxes under the EQ filters. When the Group Assign boxes are checked, the Group Settings override individual loudspeaker settings - that is, the settings defined in this window will be uploaded to all loudspeakers in the system and override the settings in the individual loudspeakers. Any items that are not assigned to the Group Settings will remain under the control of each loudspeaker; for example, if the High and Low Frequency Rolloff controls are not checked then each loudspeaker's high and low frequency rolloff can be adjusted in the individual loudspeaker's Control window. Users Manual Group Control CONTROL MODE RHAON software allows you to create Groups of loudspeakers and also set up Groups of loudspeakers within a single master Group. Clicking Add Groups in the toolbar adds a group to the System listing tree and puts a Group icon into the workspace on the right. Our example Left-Center-Right array system is a natural for 3 Groups. Toggles Group between Power On and Standby Group Name Turns "Group Mute" On & Off Turns Loudspeaker Group "Wink" lights On & Off You add Loudspeakers to the Group by dragging and dropping their listing in the Systems tree into the Group listing. When they are added to the Group, the loudspeaker icons will disappear into the Group icon. To view all the loudspeakers in the Group, click on the Expand/Collapse toggle at the lower right of the Group Icon. Expands/Collapses Loudspeaker Icons Note that loudspeakers within a group are linked to the Group Icon and cannot be individually moved around the work space. Double-clicking on the Group Icon will bring up the Group Properties window. The Connect Properties window has the same controls found in any individual loudspeaker's Properties window, except for the lack of meters and CobraNet channel selection facilities. [. . . ] · Open CobraNet Discovery -- using the same settings you use in RHAON -- to see if your loudspeaker shows up. CobraNet Discovery is a Cirrus Logic software tool that identifies and displays all CobraNet devices on a network. It is helpful in diagnosing and correcting any misconfigured equipment. CobraNet Discovery was included on your RHAON CD and can be easily installed from it. [. . . ]