User manual RENKUS-HEINZ RHAON IC-R

[. . . ] Installation & Operating Instructions RHAON Version 1. 2. 2. 14 USERS MANUAL For All Renkus-Heinz RHAON-Empowered Loudspeaker Systems Users of Renkus-Heinz Iconyx IC-R or IC Live digitally steered line arrays should refer to the Owners Manual supplied with these arrays for detailed instructions on their setup and use. Users Manual Read these instructions. Follow all instructions Do not use this apparatus near water. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on it. Install in accordance with the manufacturer's instructions. [. . . ] Underneath it are controls for 12 filters. To select a filter, click the button above its white data fields; then either type in your values, use the up-down arrows or scroll with your mouse to adjust the parameters. At the far left is a highpass filter; its lowpass counterpart is at the far right. These filters have three controls: Cutoff Frequency, Type (Bessel, Butterworth, etc. ), and Slope. The pair of filters to the inside are shelving filters, with controls for corner frequency and boost/cut. The center section gives you control of 8 fully parametric filters, with controls for center frequency, boost/cut and bandwidth in octaves. When you activate a filter, its button turns green and it appears on the graph ­ each filter appears in a different color. A solid line shows the overall EQ curve. The Bypass All button at the bottom of this section lets you compare filtered and unfiltered signals quickly. All filter parameters can be controlled with the scroll wheel on your mouse. Click inside the control field and scroll to set: Gain, Bandwidth, Frequency, etc. Below the EQ section in the light grey area, you'll find a Compressor on the left. The controls ­ Threshold, Ratio, Attack Time, Release Time and Soft Knee ­ are similar to the EQ controls. You can type in values, use the Up/Down buttons, or scroll with your mouse to find the values you want. Under Signal you will find buttons that set the compressor's trigger point Above, At or Below the Knee. When the compressor is operating, the Bypass button is red and the Gain Reduction meter on the right side of this section lights up. To turn the compressor off or compare the uncompressed output, click the Bypass button. To the right of the compression Reduction Meter is the Make-Up Gain control. This control can be used to restore RMS levels of the compressed signal to those expected of the signal pre-compression. The RHAON input module's DSP has 340 milliseconds of signal delay available if you are using the 48 kHz sample rate; 170 milliseconds if you are using 96 kHz. Use either the up-down arrows or the slider control to adjust the delay time. Priority Override is one of the unique features of RHAON. It allows you to assign signalactivated priority override capabilities to any one of the array's multiple inputs. [. . . ] It can also be downloaded free of charge from: ftp://ftp. renkus-heinz. com/Software/CNDisco342. exe or http://www. cirrus. com/dispatch/forms/sup/boardreg/breg/agree. jsp?agid=TB237&fp=/en/pubs/software/CNDisco345. exe Problem: I am attempting to do anything RHAON-related over a Wireless Access Point, or I am attempting to either control a RHAON network or pass audio over a WiFi link with no results Solution: Because of CobraNet bandwidth and latency concerns, RHAON (and CobraNet) will not work effectively over an 802. 11a/b/g/n WiFi link. 47 Users Manual FAQ and RHAON Network Troubleshooting Tips (Continued) Problem: My computer went to sleep with RHAON running and now I cannot communicate with my loudspeakers or see any of them on the network. Solution: The CobraNet Components may not be able to recover from sleep mode on some computers. This issue may be resolved in future CobraNet updates. To fix, close RHAON (and, if running, CobraNet Discovery) and bring up the Windows Task Manager (Ctrl-AltDelete). [. . . ]