User manual REVEL C12 REV A

[. . . ] . 13 Loudspeaker Volume Levels Obtaining Service . . 15 REVEL Concerta C12 Owner's Manual 3 DOCUMENTATION CONVENTIONS This document contains general safety, installation, and operation instructions for the Revel Concerta C12 Center-Channel Loudspeaker. It is important to read this document before attempting to use this product. Pay particular attention to safety instructions. WARNING Calls attention to a procedure, practice, condition, or the like that, if not correctly performed or adhered to, could result in injury or death. [. . . ] Remove the left and right pads and the grille identified in Figure 2 (right). Remove the Owner's Manual, Warranty Card and rubber pad feet as identified in Figure 2 (right). Grasping the sides of the cabinet, place the C12 on its side. Then place the C12 in the upright position. REVEL Concerta C12 Owner's Manual 7 LOUDSPEAKER OVERVIEW Figure 3: C12 Loudspeaker Front View CAUTION To prevent cabinet damage, do not use a cloth made with steel wool or use metal polish to clean the cabinet. 1 1 2 Do not use any cleaning products or polishes on the cabinet or grille. FILTER NETWORK Optimize loudspeaker on-axis and off-axis response with high-order filters at 500Hz and 2. 8kHz, helping to ensure smooth octave-to-octave balance and timbral accuracy. Gold-plated binding posts accommodate heavy speaker cables. 3 The numbers in Figure 3 (above) correspond with the numbered items in the Driver Complement section that begins below. INPUT PANEL The numbers in Figure 4 (page 9) correspond with the numbered items in this section. DRIVER COMPLEMENT The numbers in Figure 3 (above) correspond with the numbered items in this section. 1. Input Connectors Provide input connections from the associated power amplifier. One "positive" and one "negative" gold-plated binding posts are available. Refer to the Making Connections section that begins on page 11 for additional information. 1. Midrange CABINET Reduces cabinet-induced colorations with thick MDF walls and internal bracing. An adjustable tilt foot is shipped attached to the cabinet to provide an optimum tilt angle when the C12 is placed on or above a video monitor. The cabinet's vinyl finish does not require routine maintenance. However, cabinet surfaces that have been marked with fingerprints, dust, or other dirt can be cleaned using a soft cloth. 2. Adjustable Tilt Foot Provides an adjustable tilt angle if the C12 is mounted on top of a monitor or shelf for optimum sound quality. Adjust until desired tilt angle is achieved. See page 10 for more information. 8 REVEL Concerta C12 Owner's Manual Figure 4: C12 Loudspeaker Rear View 1 2 proximity to the C12. These magnetic fields decrease rapidly with distance, so moving the C12 farther away from the monitor will reduce interference. It is important to confirm that the C12 is suitable for use with the intended CRT monitor. Note The numbers in Figure 4 (above) correspond with the numbered items in the Input Panel section that begins on the previous page. DLP, LCoS and Plasma display devices are not affected by magnetic fields. LOUDSPEAKER PLACEMENT Loudspeaker fidelity depends on the following three factors: 1. Loudspeaker placement ON TOP OF MONITOR The C12 loudspeaker can be placed on top of a video monitor or a shelf as shown in Figure 5 (below). If desired, use the tilt foot to create a proper tilt angle. The loudspeaker should be tilted to align the tweeter with the listener's head. Figure 5: On Top of Monitor Advanced Revel design features allow the C12 to achieve stunning acoustical precision with exceptional freedom from coloration and distortion across a wide dynamic range. As a result, experimenting with loudspeaker placement will have the most significant impact on the C12's performance. The bulleted items that begin below indicate important placement considerations for the C12. [. . . ] A breakthrough measurement, this specification closely correlates to sound quality in a single curve ­ a long-standing goal of loudspeaker engineers. In-room response is measured through the use of large anechoic chambers. The speaker's response is measured every 10 degrees horizontally and vertically for a total of 72 response measurements. The in-room response curve is a prediction of how the speaker would measure in a typical room. [. . . ]