User manual REVEL I30 INSTALLATION REV 1

[. . . ] Disturbing the insulation in this product during installation, maintenance, or repair will expose you to fiberglass wool. Fiberglass wool is known to the State of California to cause cancer. Fiberglass wool may also cause respiratory, skin, and eye irritation. To reduce exposure to this substance or for further information, consult material safety data sheets available from the address shown below, or contact your supervisor. · · Harman Specialty Group 3 Oak Park Drive Bedford, MA 01730 4 REVEL I20/I30 Back Box Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Read Before Starting Installation WARNING This enclosure is not listed for use in air handling plenums. [. . . ] See the illustrations below for inner dimensions. Installation Instructions The following items are required for installation: · · · · · · · · · · · · tape measure carpenter's level pencil hammer nails drywall section drywall screws staples/U nails utility knife service wire (included) work gloves face mask Caution The back box should be installed by a professional. Installers must adhere to local building codes to ensure a proper installation. Harman Specialty Group is not responsible for any injury or damage caused by improper installation. Figure 1: I20 Back Box Height & Width Figure 2: I30 Back Box Height & Width 13. 57-inches (344. 7mm Place side flange on top of stud 13. 57-inches (344. 7mm This flange fits in between wall studs 16. 78-inches (426. 2. mm) 10. 65-inches (270. 5mm) 28. 62-inches (727mm 12. 50-inches (317. 5mm) 21. 16-inches (537. 5mm) 19. 22-inches (488. 2mm) 28. 62-inches (749. 3mm) 14. 84-inches (376. 9mm) In-wall fits here 17. 50-inches (444. 5mm) 17. 50-inches (444. 5mm) 6 REVEL I20/I30 Back Box Installation Instructions Figure 3: I20/I30 Back Box Depth 3. 375-inches (85. 7mm) Figure 4: Place the Back Box between Wall Studs Rear Front To install the back box: Note Figure 3 (above) shows the depth of the back box. It can be installed in walls constructed with standard 2x4s. It is important to note that the speaker mounting frame requires a minimum depth (from the wall face to the inside back of the I20/I30 Back Box) of 3-1/2 inches (88. 9mm) for proper installation. This can only be achieved by using 5/8 inch (15. 9mm) sheetrock on the wall face. It is recommended the installer consult with the sheetrock installer before beginning the installation. 1. Use a tape measure to determine the location where the speaker is to be mounted. Refer to the Revel I20/I30 In-Wall Loudspeaker Owner's Manual for speaker placement considerations. Record exact measurements from the floor, ceiling and an adjacent dry wall section. Note The I20/I30 Back Box eliminates sensitivity to placement considerations due to standing waves within the wall cavity as described in the Revel I20/I30 In-wall Loudspeaker Owner's Manual. Caution Installers are advised to wear work gloves and face mask when installing the back box and making wire connections, as the back box contains fiberglass. Position the back box between two wall studs and into the wall cavity as shown in Figure 4 (above). The back box must be placed between standard 16-inch on-center stud spacing. If desired, the back box can be mounted upside-down if you will be mounting the speaker close to the ceiling. REVEL I20/I30 Back Box Installation Instructions 7 Figure 5: Fasten Back Box to Wall Studs Note The terminal cup can be removed from inside the back box if it is necessary to retighten the amplifier cable connections. Figure 6: Amplifier Connections Back Box Terminal Cup Binding Posts 3. Firmly secure the back box into place using nails as shown in Figure 5 (above). - + Power Amplifier Caution Installers must adhere to local building codes to ensure a proper installation. Harman Specialty Group is not responsible for any possible damages caused by improper installation. 5. Insert the amplifier wire and retighten the connectors by hand (clockwise). When making connections, use the tie wrap mount located next to the binding posts to wrap cable ties for strain relief. 4. Connect the power amplifier cables to the outside of the back box terminal cup as shown in Figure 6 (next column). Loosen the terminal connectors by hand (counterclockwise) on the terminal cup's positive (+) and negative (-) binding posts. Caution Be sure to comply with local wiring codes. Harman Specialty Group is not responsible for any damages or injuries that may result from faulty wiring. 8 REVEL I20/I30 Back Box Installation Instructions 6. [. . . ] Be sure to avoid contact with the speaker cone. Figure 8: Route Terminal Cup Wires to top of the Loudspeaker REVEL I20/I30 Back Box Installation Instructions 9 Figure 9: Speaker Connections A In-wall Speaker Rear B C Make Connections Observing Proper Polarity Binding Posts Insert Banana Plugs into exposed holes Exposed Binding Post Terminal Connectors 13. Locate the loudspeaker's binding posts as shown in illustration A of Figure 9 above. From the top of the speaker, run the terminal cup wires down to the loudspeaker's binding posts as shown in illustrations B and C above. If necessary, use the extra service wire (provided). [. . . ]