User manual REVEL M10 REV 0

[. . . ] If you suspect damage from transit, report it immediately to your dealer and/or delivery service. Keep the shipping carton and packing materials for future use. Open the package and verify the following contents: Part A Part B (2) Wall-mount end caps (attached to satellite) (1) Flat-head Phillips screw 1/4-20 x 1-1/4" (1) Pan-head Phillips screw 1/4-20 x 3/4" (1) Satellite speaker (1) Wall bracket with wall bracket cover (6) Flat-head Phillips screws 1/4-20 x 7/8" (2) Pan-head Phillips screws 1/4-20 x 1" (3) 1/4-20 Flat washers (1) Bottom foot (3) 1/4-20 Nuts (1) Medium collar (1) Allen wrench (1) Table stand plate (1) Small collar (1) Large collar 3 Planning Your System Before deciding where to best place your speakers, survey your room and study Figures 1 and 2. Center Channel (above or below video screen) Placement Note: The satellite speakers can be placed directly on a shelf or tabletop, using one of the three included shelf stands, or mounted on a wall using the included wall brackets. Optional floor stands are also available. [. . . ] If you choose the shortest stand, follow steps two to four on page 6. If you choose either of the taller stands, follow steps two to five on page 7. 30-1/2" 27" 27" 23-3/8" 8" 4" 4" 7/8" Small Medium Large 5 Step Two For Small Table Stand Assembly Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on the bottom. Step Three For Small Table Stand Assembly Assemble the table stand plate, the small section and the foot. Place three nuts (provided) in the base of the foot and secure them in place by inserting three screws (provided) through the top of the table stand plate. (3) 1/4-20 x 7/8" Flat-head screws Table stand plate Satellite speaker Small section/collar End cap Foot Revel logo (3) 1/4-20 Nuts 1/4-20 x 3/4" Screw Step Four For Small Table Stand Assembly Run the speaker wire through the base, and screw the foot assembly to the speaker assembly. Note: The bottom is the end closest to the Revel logo on the front grille and the speaker connections on the rear. Speaker wire 1/4-20 x 1-1/4" Flat-head screw 6 Step Two For Medium and Large Table Stand Assembly Using the included Allen wrench, remove the bottom end cap of the loudspeaker by unscrewing the single center screw on the bottom. Step Four For Medium and Large Table Stand Assembly Use the screw and washer to attach the medium or large base assembly to the speaker assembly, as shown. Satellite speaker End cap Revel logo Flat washer 1/4-20 x 1" Pan-head screw 1/4-20 x 3/4" Pan-head screw Flat washers 1/4-20 x 1" Pan-head screw 1/4-20 x 3/4" Screw Step Five For Medium and Large Table Stand Assembly Run the speaker wire through the table stand plate. Use three screws (provided) to attach the plate to the bottom of the base assembly. Note: The bottom is the end closest to the Revel logo on the front grille and the speaker connections on the rear. Step Three For Medium and Large Table Stand Assembly Run the speaker wire through the collar. Using three screws, attach the table stand plate to the medium or large section, as shown. (3) 1/4-20 x 7/8" Flat-head screws Speaker wire Speaker wire (3) 1/4-20 x 7/8" Flat-head screws 7 Wall-Mounting the M10 Using the Included Wall Bracket The customer is responsible for the proper selection and use of mounting hardware, and for correctly and safely wall-mounting the speakers. Step Four Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on bottom. End cap Step One Remove the wall-bracket cover by removing the four wall bracket screws on the ends, as shown. Satellite speaker End cap Revel logo Step Two Run the speaker wire behind the wall bracket and out through the hole at the bottom. After deciding where to place the satellite speaker, attach the wall bracket (in a vertical position) to the wall, using the appropriate screws and anchors. 1/4-20 x 3/4" Screw Mounting screws and anchors not included Note: The bottom is the end closest to the Revel logo on the front grille and the speaker connections on the rear. Wall bracket Step Five Connect the wires (see page 9). Replace the end caps while capturing the wall bracket in between parts A and B and securing it in place. Tighten until snug. Bottom hole Step Three Run the speaker wires out through the bottom hole of the wall bracket cover. Resecure in place, as shown, with four of the wall bracket screws. Wall-mount end cap A Wall-mount end cap B 8 Step Six The wall-bracket design allows for rotation of the speakers at angles up to 30º of center. Position the speakers so that they face toward the primary listening position, before fully tightening. ­ + Figure 3: This example shows how to connect bare wires to the terminals. Banana plugs may also be inserted directly into the rear of the connector. Wiring the Speaker After placing the speaker, you are ready to connect it to your system. Use high-quality speaker wire to make the connections. Consult the owner's manuals included with your amplifier or receiver, for connection and operation procedures. 1. Inset bare ends; tighten terminals. Important!DO NOT reverse polarities (+ to ­ or ­ to +) when making connections. Doing so will degrade the imaging and bass response of the home theater system. After correctly placing and wiring the M10 and the rest of your speaker system, adjust the levels for all of the channels as recommended by the manufacturer of your receiver/processor. Surround Modes When using the system in a Dolby® Digital or DTS® home theater system, make sure the receiver or processor is set to "Small" for all M10 loudspeakers. Some receivers/processors offer a choice of crossover frequencies. [. . . ] The dealer from whom the Revel products were purchased was authorized to sell such products at the time of the original purchase. The original, dated Bill of Sale is presented whenever service is required during the warranty period. The balance of this warranty is transferable only if the used product is purchased from an authorized Revel dealer. This warranty is only valid for service within the United States, its territories and Canada; please contact an authorized Revel dealer for warranty and service information. [. . . ]