User manual REVEL ULTIMA STUDIO 2 REV 1

[. . . ] Ultima Salon® 2 - Ultima Studio® 2 Revel® Loudspeaker Owner's Manual Harman Specialty Group 3 Oak Park Drive Bedford, MA 01730-1413 USA Tel 781-280-0300 Fax 781-280-0490 www. revelspeakers. com Customer Service Telephone: 781-280-0300 Sales Fax: 781-280-0495 Service Fax: 781-280-0499 Product Shipments: HSG/Revel Returns Dept. 75th Avenue Phoenix, AZ 85043 Part No. 354898-001 | Rev 1 | 12/07 "Revel, " "Ultima Salon, " "Ultima Voice", " Ultima Studio, " "Ultima Gem, " and the Revel logo are trademarks or registered trademarks of Harman International Industries, Inc. patent numbers and other worldwide patents issued and pending. ©2007 Harman International Industries, Inc. [. . . ] These are reflection points that require acoustic treatment materials. If acoustic treatment materials are not available, hanging a rug over the reflection points will help reduce degradation in overly "live" rooms. Carpeting the floor between the loudspeakers and the primary listening position and placing irregular surfaces such as bookcases at first reflection points will also help minimize strong reflections. Avoid placing large reflective surfaces such as coffee tables between the loudspeakers and the listeners for critical listening. COMBINATION SPIKES/GLIDES When shipped, combination spikes/glides, shown in the next page in Figure 6 and 7, are not attached to the bottom of the cabinet. For optimal stability and to accommodate installations on tile, hardwood, and carpeted floors, you can install the combination spikes/glides. Use the glide side to protect tile and hardwood floors. Caution When moving the Salon or Studio2, avoid dragging it across the floor. If the Salon2 or Studio2 are placed on a carpeted floor, the spikes/glides should be adjusted with the sharp end protruding from the cabinet. The spikes/glides should be used so that the smooth "glide" end is exposed to protect tile, hardwood floors and furniture. To install the combination spikes/glides: 1. Place the speaker on its side on a soft towel or carpeted floor. Select the appropriate end of the spike/glide, depending on your surface. If the speaker is to be used on a hardwood floor or smooth surface, use the glide end of the spike. Locate the four threaded insets on the bottom of the speaker. Screw the first spike into the threaded insert, making sure to include the locking ring and felt washer in the order shown. Repeat step 4 for the remaining three spikes. Make sure all spikes are evenly threaded to achieve a level balance. 12 Ultima Salon2/Studio2 Owner's Manual Figure 6: Combination Spike/Glide Components MAKING CONNECTIONS The Salon2/Studio2 features gold-plated binding posts and jumper straps that allow it to be configured for single-wired, Bi-wired, or Bi-amplified connections. Felt Washer Locking Ring Caution Never make or break connections unless all system components are powered off. Remove the input panel jumper-straps identified in Figure 4, page 9, before making bi-wired or bi-amplified connections. Failure to do so may cause damage to some power amplifiers. Before making connections, note the following: · The standard connection method uses a single loudspeaker cable. The Salon2/Studio2 are equipped with two pairs of input terminals to allow for bi-wiring or bi-amplification. While Revel does not endorse one particular connection method over another, these additional connection options are available if desired. The design of this loudspeaker is such that optimal performance can be attained using the standard connection method. [. . . ] If a Revel loudspeaker must be returned for repair, Harman Specialty Group will assume no responsibility for the loudspeaker during shipment from the customer to Harman Specialty Group, whether the loudspeaker is or is not covered under warranty. To contact Harman Specialty Group Customer Service: Telephone: Service Fax: Sales Fax: 781-280-0300 781-280-0499 781-280-0495 Product Shipment Directions: The following information must be included when a loudspeaker is returned for service: · · · · · · · · Name Company name Street address, city, state and, zip code Telephone number including area code and country code (if applicable) Loudspeaker serial number A detailed description of the problem The preferred method of return shipment RMA number clearly marked on both the inside and outside of the package Do not return accessories such as owner's manuals unless instructed to do so. www. revelspeakers. com All Returns must be: · · · Well-packaged using the original packing materials Properly insured and consigned Pre-paid to a reliable shipping agent Product Shipments: HSG/Revel Returns Dept. 75th Avenue Phoenix, AZ 85043 26 Ultima Salon2/Studio2 Owner's Manual LIMITED WARRANTY A valid serial number is required for warranty coverage. This Revel warranty protects the original retail purchaser for a period of five (5) years (parts and labor) from any failure as a result of original manufacturing defects so long as: 1. [. . . ]